Exabyte EZ17A Скачать руководство пользователя страница 141

Страница: 141 / 168

Specifications

Installation and Operation

125

The cord must be harmonized to CENELEC publication
HD-21. The electrical characteristics and rating must be
minimum H05VVF3G0.75 (6 A).

SCSI cable specifications

When selecting a cable to connect the autoloader to the SCSI bus,
select a cable that complies with the SCSI-3 specification and
meets the requirements listed in the following table.

➤

Important

To comply with the regulations and

standards listed at the front of this book, all SCSI
cables you use with the autoloader must be
properly shielded.

Narrow SCSI configuration

Wide SCSI configuration

Connector type (to
autoloader)

50-pin, high-density, shielded,
male connector and 50-pin to
68-pin adapter

A SCSI adapter is required w hen connecting a narrow SCSI cable to the autoloader (see

page 128

68-pin, high-density, shielded,

male connector

Recommended
impedance

Single-ended: 132 ohms

LVD: 110 ohms

HVD: 88 ohms

Содержание EZ17A









































































































































































Результаты поиска

Содержание EZ17A

Отзывы:

Exabyte EZ17A, Инструкция по установке и эксплуатации, Страница: 141 / 168

Результаты поиска

Содержание EZ17A

Отзывы: