Exabyte EZ17A Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 168

Exabyte EZ17A Скачать руководство пользователя страница 146

Appendix B

130

Exabyte EZ17M and EZ17A

Considerations for installing the autoloader on
the SCSI bus

This section provides the basic guidelines and considerations for
setting up the autoloader on the SCSI bus.

LVD SCSI

The autoloader uses an LVD (low-voltage differential) SCSI
configuration. Every SCSI device attached to the SCSI buses
connecting to or from the autoloader must also be LVD.

Note:

Although LVD SCSI is compatible with single-ended SCSI,
Exabyte does not support single-ended devices on the
autoloader’s LVD SCSI bus.

Do not connect the LVD autoloader to a high-voltage differential
(HVD) SCSI bus.

Wide SCSI

The autoloader is available in a wide configuration only. If
desired, you can attach the autoloader and drive to a narrow SCSI
bus using adapters available from Exabyte. However, attaching
the drive to a narrow bus will significantly reduce performance.

If you want to connect the autoloader to a narrow SCSI bus, you
must use a 50-pin to 68-pin LVD SCSI adapter. Make sure that the
adapter terminates all unused data lines.

«
...
144
145
146
147
148
...
»

Содержание EZ17A









































































































































































Отзывы:

Нет отзывов