Exabyte EZ17A Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 168

Exabyte EZ17A Скачать руководство пользователя страница 94

Chapter 5

78

Exabyte EZ17M and EZ17A

If the LCD still displays

ClnSoon

or

MustCln

, replace the

cleaning cartridge and clean the drive again. If the message is
still on the autoloader LCD, or the drive LEDs are still on after
the second cleaning, there may be a problem with the drive.

➤

Important

If the drive ejects the cleaning

cartridge immediately after loading it and the LCD
displays the message

Depleted

, you need to

replace the cleaning cartridge. To order cleaning
cartridges, contact Exabyte (see

on the inside back cover).

5.

Replace the cartridge magazine.

➤

Important

Before reinstalling the magazine,

make sure there is not a cartridge in the drive. If
you install the magazine when there is a cartridge
in the drive, the autoloader cannot complete its
power-on self-test and will display an error.

«
...
92
93
94
95
96
...
»

Содержание EZ17A









































































































































































Отзывы:

Нет отзывов