Evco EVJ 700 Скачать руководство пользователя страница 6

Страница: 6 / 52

EVJ 700

EVJ 700 ----

Application Manual:

144EVJ700E204

EVCO | 29.01.2021

| 6

Main features and purchasing codes

The table below shows the main features and their purchasing codes

Features

EVJ705J9

EVJ705Z9

EVJ725J9

EVJ705J9VG

Power supply

115... 230 VAC

•

Installa

Installation

tion

Recessed in the panel

•

Concealed under the panel (if made of glass or
metacrylate)

•

Analogue inputs

Regulation probe (Pt 1000 2 wires)

•

Regulation probe (J/K/Pt 100 2 wires)

•

Needle probe (Pt 1000 2 wires)

•

Needle probe (J/K/Pt 100 2 wires)

•

Digital inputs

Multi-purpose 1

•

Multi-purpose 2

•

Digital outputs (electro

Digital outputs (electro----mechanical relays, A res.

mechanical relays, A res.

at 250 VAC)

Load 1 (configurable)

16 A

Load 2 (configurable)

5 A

8 A

5 A

Load 4 (configurable)

8 A

Load 5 (configurable)

8 A

5 A

8 A

Load 6 (configurable)

5 A

Digital outputs

Digital outputs (command for solid state relays; 12

(command for solid state relays; 12

VDC, 15 mA max)

Load 2 (configurable)

•

Load 6 (configurable

•

User interface

2.8 inch graphic display

•

Communications ports

TTL MODBUS

•

For encoder

•

Further features

Alarm buzzer

•

ON-OFF/PI control

•

For more information see the section “Technical specifications”.

Содержание EVJ 700





















































Результаты поиска

Содержание EVJ 700

Отзывы:

Похожие инструкции для EVJ 700

Бренды по названию

Популярные бренды

Evco EVJ 700, Руководство по применению

Результаты поиска

Содержание EVJ 700

Отзывы:

Похожие инструкции для EVJ 700

Бренды по названию

Популярные бренды