manualshive.com logo in svg

ESD C.3032.02, Руководство пользователя, Страница: 91 / 120

Поделиться
Скачать
ESD C.3032.02 Скачать руководство пользователя страница 91

Device Profile Area

CAN-CBX_Pt100    

Manual • Doc.-No.: C.3032.21 / Rev. 1.1

Page 91 of  120

8.10.9 AI Status (6150

h

)

Index

Sub-

index

Description

Value range

Default

Data type

Access

mode

6150

h

0

Number_of_entries

4

4

unsigned 8

ro

1

AI_status_1

0...5

-

unsigned 8

ro

2

AI_status_2

0...5

-

unsigned 8

ro

3

AI_status_3

0...5

-

unsigned 8

ro

4

AI_status_4

0...5

-

unsigned 8

ro

Description of the variable AI_status_x (x = 1...4):
These variables return the state of the corresponding analog input channel.

Bit:

7

6

5

4

3

2

1

0

Meaning:

reserved

*

4)

not supported *

4)

reserved

*

4)

Negative

Overload

Positive

Overload

Not Valid

*

4)

 These bits are always returned as ‘0’.

Value range:

Description

Negative overload limit

Positive overload limit

PT-sensors

-200.715 

D

C

853.498 

D

C

Ni-sensors

-200.000 

D

C

399.138 

D

C

electric resistance measurement 

at default setting 

 -

-

A bit is active (set to ‘1’), if the lower or the upper limit is exceeded. The bits 1 and 2 cannot be set
at the same time.

If no sensor is connected, only bit “Not Valid” is set. 
If the temperature exceeds the range, bits “Not Valid” AND the corresponding  “Overload”-bit are
set.

Valid return messages are e.g.:

AI_Status_1 = 00

h

  :  no error

AI_Status_1 = 03

h

  :  positive overload and sensor value not valid (e.g. no sensor identified)

Содержание C.3032.02

























































































































Отзывы:

Нет отзывов