ELTEX LTP-4X Скачать руководство пользователя страница 59

Страница: 59 / 199

LTP-8X(config)# logging rsh loglevel info
LTP-8X(config)# logging file loglevel none

Step 4.

To view SYSLOG configuration, use the

do show logging settings

command.

LTP-8X(config)# do show logging settings

Log:

Remote syslog: 192.168.1.43

Port: 514

Size: 16384

Save logs between boots: true

Log input commands: false

Destinations:

System: notice

Console: notice

Remote shells: info

File: none

TP-8X#

Step 5.

Apply the configuration by using the

commit

command.

LTP-8X(config)# do commit

14.5

ALARMD Configuration

ALARMD is a terminal alarms manager. Alarms manager enables troubleshooting and provides

information about important events related to terminal operation.

A record in active alarms log (an event) corresponds to an event, which happened in the terminal. Types

of events and their descriptions are provided in Table 14.4.

Table 14.4 – Types of Events in the Active Alarms Log

Event

Description

Threshold

ram

Free RAM size decreased to the threshold

30% *

User tried to log in or logged in using their
credentials

config_save

User saved the configuration

firmware_update

LTP-8X firmware update completed
successfully / with errors

duplicate_mac

Two devices with the same MAC addresses
detected

physical_layer_flapping

Flapping on Ethernet ports

pon-gpon_port_no_ont

The first ONT connected / the last ONT
disconnected on channel

ont_physical_layer

ONT connected/disconnected

olt_update

OLT chip firmware update completed
successfully / with errors

ont_update

ONT chip firmware update completed
successfully / with errors

gpon-port_flapping

GPON interface flapping

Содержание LTP-4X








































































































































































































Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды

ELTEX LTP-4X, Руководство по эксплуатации

Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды