ELTEX LTP-4X Скачать руководство пользователя страница 36

Страница: 36 / 199

9.3

CLI Command History

Sometimes it might be necessary to execute the same set of operations several times. To make the work

with repeating commands easier, the terminal CLI keeps the command history.

The list of previously entered commands can be displayed with the help of the

show history

command:

LTP-8X# show history

Last CLI commands:

show version

configure terminal

exit

show historyLTP-8X#

Use the

and

Down

cursor keys to scroll the command history and the

Enter

key to execute the

selected command.

LTP-8X# <Up>
LTP-8X# show management <Up>
LTP-8X# switch <Up>
LTP-8X# exit <Up>
LTP-8X# show uptime <Up> up 1 day, 23:44

9.4

Group Operations

Group operations can be performed on such terminal configuration objects as interfaces and ONT. It is

especially convenient, when you have to apply the same actions to multiple objects.

To perform a group operation, select the range of object IDs instead of one object ID. This feature is

supported by a majority of CLI commands.

For example, enable fec for all ONTs in a certain channel.

LTP-8X(config)# interface ont 0/0-127
LTP-8X(config)(if-ont-0/0-127)# fec

Or view the list of active ones in the first 4 GPON channels:

LTP-8X# show interface ont 0-3 ont online

GPON-port 0 has no online ONTs
GPON-port 1 has no online ONTs
GPON-port 2 has no online ONTs GPON-port 3 has no online ONTs
Total ONT count: 0

Содержание LTP-4X








































































































































































































Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды

ELTEX LTP-4X, Руководство по эксплуатации

Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды