ELTEX LTP-4X Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 199

background image

93

PPPoE Intermediate Agent also limits the number of simultaneous PPPoE sessions. The

restriction can be set for both the total number of terminal sessions and for every ONT
separately.

23.1

PPPoE Intermediate Agent Profiles Configuration

To configure a PPPoE Intermediate Agent profile, the following steps should be taken.

Step 1.

Switch to the PPPoE Intermediate Agent profile.

LTP-8X# configure terminal
LTP-8X(config)# profile pppoe-ia pppoe-ia-00
LTP-8X(config-pppoe-ia)("pppoe-ia-00")#

Step 2.

Enable PPPoE traffic processing with the

enable

command.

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# enable

Step 3.

Specify the vendor specific tag format with the help of the

format circuit-id

and

format remote-id

commands. A list of possible tokens is given in Table 19.1.

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# format circuit-id "%HOSTNAME%"
LTP-8X(config-pppoe-ia)("pppoe-ia-00")# format remote-id "%PONSERIAL%:%GEMID%"

Step 4.

Enable DoS attack protection with the help of the

dos-block

command if needed.

Specify a threshold for the number of DHCP queries per second that will block queries when
exceeded. Use the

dos-block packet-limit

command for it. Use the

dos-block block-time

command to specify the blocking time in seconds.

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# dos-block
LTP-8X(config-pppoe-ia)("pppoe-ia-00")# dos-block packet-limit 200
LTP-8X(config-pppoe-ia)("pppoe-ia-00")# dos-block block-time 300

Step 5.

Set the limits of PPPoE sessions by using the

sessions-limit

command.

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# sessions-limit 128 per-user 2

If there is no need to limit sessions for all ONTs, pass 'unlimited' parameter in 'session-limit
per-user' command:

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# sessions-limit per-user unlimited

If  you  need  to  disable  limiting  session  for  specified  ONT  (might  be  useful  for  SFP-ONU)  and
save  limiting  for others,  define  limiting  globally  in  the  profile  and  disable  it  in  the  'interface
ont' settings:

LTP-8X(config-pppoe-ia)("pppoe-ia-00")# sessions-limit 8192 per-user 2
LTP-8X(config-pppoe-ia)("pppoe-ia-00")# exit
LTP-8X(config)# interface ont 0/0
LTP-8X(config)(if-ont-0/0)# pppoe-sessions-unlimit

Step 6.

Apply the changes by using the

commit

command.

«
...
91
92
93
94
95
...
»

Содержание LTP-4X








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LTP-4X

Бренд: Aastra Страницы: 2

Бренд: i-MO Страницы: 58

Бренд: Laird Страницы: 36

Pixie-4 Express

Бренд: XIA Страницы: 17

Бренд: Draytek Страницы: 8

Бренд: Oracle Страницы: 24

Бренд: Fortinet Страницы: 20

Бренд: Orban Страницы: 255

Бренд: Stephen Страницы: 102

Бренд: Buffalo Страницы: 2

Бренд: red lion Страницы: 5

Elite Controller

Бренд: RANA Systems Страницы: 328

UM10301 PCA8565

Бренд: NXP Semiconductors Страницы: 54

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: Kontron Страницы: 98

Бренд: Federal Signal Corporation Страницы: 49

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: Intel Страницы: 105

Бренд: NETGEAR Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды