ELTEX LTP-4X Скачать руководство пользователя страница 105

Страница: 105 / 199

105

Chapter 26.

ONT Licensing

Introduction

By default, OLT supports only Eltex ONTs operation. To enable any third-party ONTs, OLT requires a license.

To purchase the license, contact Eltex Marketing Department.

If a third-party ONT is connected to OLT without a license, the following entry will be
made in the log file:

Jul 4 11:10:14 LTP-8X pmchal: error: [ONT2/0] License is not valid, configuration will not continue

26.1

Loading a License File to OLT

A license is a text file of the following format:

{

"version":

"<VER>",

"type":

"all",

"count":

"<count>",

"sn":

"<SN>",

"mac":

"<MAC>",

"sign":

"<hash>"

}

Where:

VER

—license file version number;

count—

number of third-party ONTs enabled on the OLT;

SN—

LTP serial number;

MAC—

LTP MAC address;

hash—

license file digital signature.

There are two ways to load a license to OLT:

Use the

copy

command:

LTP-8X# copy tftp://<IP>/<PATH> fs://license
Download file from TFTP-server..
License successfully installed. Please reboot device for changes to make effect

Содержание LTP-4X








































































































































































































Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды

ELTEX LTP-4X, Руководство по эксплуатации

Результаты поиска

Содержание LTP-4X

Отзывы:

Похожие инструкции для LTP-4X

Бренды по названию

Популярные бренды