Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 206

Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 50

15P0082B8

USER MANUAL

SINUS/ISD

5 - 8/14

5.4.7 MENU SHORTCUTS AND SPECIAL KEY COMBINATIONS

5.4.7.1

Quick Link Information

When in Advanced view level, pressing the M

M key for approximately 3 seconds in any parameter will display link

information about that parameter (a message may be displayed during this time). The information is displayed in
the following format:

325- - - 7 ->[245]

Source tag number

Link number

Destination tag number

Note:

The Inverter must be in Configuration mode before links can be edited. However, holding the M

M key

down in Parameterisation mode will allow the information to be displayed but the information disappears
when the key is released.

Use the up (

∆∆

)

) and down (

∇

∇

)

) keys to change the source tag number. If the source number is changed from

zero, the next available link number will be assigned. Press E

E twice to clear the link information and return to the

parameter.
All link information is also available through the menu LINKS, menu at level 2.

5.4.7.2

Quick Save to Memory

Holding down the PROG

PROG key for about 2 seconds quickly takes you to the SAVE TO MEMORY menu in the

PARAMETER SAVE menu at level 1.
After saving, press the PROG key to return to the previous display.

5.4.7.3

Changing the Display Language

Holding down the PROG

PROG key at power-up takes you immediately to the DISPLAY LANGUAGE parameter in the

MENUS menu at level 1.
Refer to “Selecting the Display Language”, page 5-10/14 for information on selecting a language.
The selected view level (when previously powered-down) determines how you will exit the parameter:

•

Operator:

releases you into the OPERATOR menu at level 1

•

Basic:

releases you into the MENUS menu at level 1

•

Advanced:

releases you into the MENUS menu at level 1

5.4.7.4

Quick Drive Copy

With an application stored in the Operator Station (refer to “ Copying an
Application”, page 5-12/14), holding the down (

∇

∇

)

) key at power-up takes

you immediately to the ALL PARAMETERS display in the LOAD FROM OP
menu at level 2. The Advanced view mode is automatically selected..

Note:

Pressing the up (

∆∆

)) key, as instructed, copies all parameter settings

including motor specific data from the Operator Station to the
Inverter.

The Operator Station will still contain the application data, allowing transfer to successive units. This information
is replaced by any subsequent SAVE TO OP operation.

HEALTH

LOCAL

SEQ

REF

1

1

`UP` FOR ACTION

ALL PARAMETERS

«
...
48
49
50
51
52
...
»

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов