Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 206

Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 116

15P0082B8

USER MANUAL

SINUS/ISD

6 - 60/82

6.4.1.38

SLIP COMP

The slip compensation function block
allows the inverter to maintain motor
speed in the presence of load
disturbances.

Functional Description

Based on the rated speed, the no load speed and the rated load of the motor, the slip compensation block
adjusts the demand frequency to compensate for any speed slippage resulting from the load.

MMI Menu Map

1

SETUP PARAMETERS

2

FUNCTION BLOCKS

3

MOTOR CONTROL

4

SLIP COMP

SLIP ENABLE

NAMEPLATE RPM

MOTOR POLES

SLIP MOTOR LIMIT

SLIP REGEN LIMIT

SLIP COMP

SLIP COMP

FALSE – [ 82] ENABLE

––

1420 n/min –– [ 83] NAMEPLATE RPM ––

4 –– [ 84] MOTOR POLES

––

120.0 n/min –– [ 85] MOTORING LIMIT

––

120.0 n/min –– [ 86] REGEN LIMIT

––

Parameter Descriptions

Parameter Descriptions

ENABLE

ENABLE

Range: FALSE / TRUE

For the slip compensation to be operational this must be TRUE.
NAMEPLATE RPM

NAMEPLATE RPM

Range: 0 to 15000 n/min

This is the rated speed of the motor at rated load.
MOTOR POLES

MOTOR POLES

Range: Enumerated - see below

The number of motor poles. The values that this parameter may take are:

Enumerated Value

:

Number of poles

0 : 2
1 : 4
2 : 6
3 : 8
4 : 10
5 : 12

MOTORING LIMIT

MOTORING LIMIT

Range: 0.0 to 600.0 n/min

The maximum trim that will be produced by the slip compensation block when the
motor is driving the load (motoring).
REGEN LIMIT

REGEN LIMIT

Range: 0.0 to 600.0 n/min

The maximum trim that will be produced by the slip compensation block when the
motor is being driven by the load, (regenerating).

Speed

Rated
Speed

No Load Speed
(synchronous speed)

Rated
Torque

Torque

«
...
114
115
116
117
118
...
»

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов