Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 206

Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 111

SINUS/ISD

15P0082B8

USER MANUAL

6 - 55/82

REMOTE REVERSE

REMOTE REVERSE

Range: FALSE / TRUE

For remote setpoints, setting this parameter TRUE inverts the demanded direction of
motor rotation.
REM TRIP RESET

REM TRIP RESET

Range: FALSE / TRUE

On a transition to TRUE, this input clears latched trips.
TRIP RST BY RUN

TRIP RST BY RUN

Range: FALSE / TRUE

This allows the rising edge of run command to clear latched trips.
POWER UP START

POWER UP START

Range: FALSE / TRUE

If TRUE, this allows the inverter to go directly to run mode if in remote and a run
command is present. If FALSE, a low to high transition of the run command is required.
TRIPPED

TRIPPED

Range: FALSE / TRUE

Indicates that there is a latched trip present.
RUNNING

RUNNING

Range: FALSE / TRUE

Indicates that that the inverter is in the enabled state.
JOGGING

JOGGING

Range: FALSE / TRUE

Indicates that the inverter is in the JOG mode.
STOPPING

STOPPING

Range: FALSE / TRUE

Indicates that the inverter is stopping.
OUTPUT CONTACTOR

OUTPUT CONTACTOR

Range: FALSE / TRUE

Output to be used to drive an external contactor in the motor output. This contactor is
normally closed unless a Trip condition has occurred or the inverter goes into the re-
configuration mode.
SWITCH ON ENABLE

SWITCH ON ENABLE

Range: FALSE / TRUE

Sometimes referred to as READY TO SWITCH ON, this parameter indicates that the
inverter will accept a run command.
SWITCHED ON

SWITCHED ON

Range: FALSE / TRUE

Indicates that the inverter’s power stack is operable and the inverter will run if enabled.
READY

READY

Range: FALSE / TRUE

Output indicating that the inverter has accepted the run command.
SYSTEM RESET

SYSTEM RESET

Range: FALSE / TRUE

Output TRUE for a single cycle after the inverter enters either RUN or JOG mode.
MAIN SEQ STATE

MAIN SEQ STATE

Range: Enumerated - see below

This parameter indicates the current sequencing state:

Enumerated Value

:

State

0 : NOT READY
1 : START DISABLED
2 : START ENABLED
3 : SWITCHED ON
4 : ENABLED
5 : F-STOP ACTIVE
6 : TRIP ACTIVE
7 : TRIPPED

REMOTE REV OUT

REMOTE REV OUT

Range: FALSE / TRUE

This parameter indicates the current state of remote direction and RUN REV. Note - this
is the demanded direction, not the actual direction.
HEALTHY

HEALTHY

Range: FALSE / TRUE

Set FALSE when the inverter trips, and set TRUE when the the run command is
removed.

«
...
109
110
111
112
113
...
»

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов