manualshive.com logo in svg

Elettronica Santerno SINUS/ISD 200 S-0.75, Руководство пользователя, Страница: 143 / 206

Поделиться
Скачать
Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 143

SINUS/ISD

15P0082B8

USER MANUAL

8 - 1/2

8.0

8.0

 

R

R

OUTINE 

OUTINE 

M

M

AINTENANCE AND 

AINTENANCE AND 

R

R

EPAIR

EPAIR

8.1

8.1

 

ROUTINE MAINTENANCE

ROUTINE MAINTENANCE

Periodically inspect the Inverter for build-up of dust or obstructions that may affect ventilation of the unit. Remove
this using dry air.

8.2

8.2

 

REPAIR

REPAIR

There are no user-serviceable components.

IMPORTANT:

 

MAKE NO ATTEMPT TO REPAIR THE UNIT - RETURN IT TO ELETTRONICA SANTERNO.

8.2.1

 

 SAVING YOUR APPLICATION DATA

Although the Inverter retains saved settings during power-down, it would be wise for you to keep your Operator
Station. If your last SAVE TO OP function was made on this unit before the fault occurred, then the Operator
Station will still hold your application data. You can transfer this back into the repaired unit, if necessary. You
may, depending upon your knowledge of the fault, attempt the back-up of your application data now, refer to
Chapter 5: “The Operator Station” - Copying an Application.
If the fault clearly lies within the Operator Station, then return it for repair.

8.2.2

 

 RETURNING THE UNIT TO ELETTRONICA SANTERNO

Please have the following information available:

•

 

The model and serial number - see the unit’s rating label

•

 

Details of the fault

Contact your nearest Elettronica Santerno Service Centre to arrange return of the item.
Pack and despatch the item in the original packing materials; or at least an antistatic enclosure. Do not allow
packaging chips to enter the unit.

Elettronica Santerno SpA

Via G. Di Vittorio 3

40020  Casalfiumanese  (BO)

(Italy)

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов