Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 176

Страница: 176 / 206

15P0082B8

USER MANUAL

SINUS/ISD

12 - 4/8

THE E.S. EC DECLARATION OF

CONFORMITY FOR EMC IS VALID

FOR THE SPECIFIED E.S. MODULE

START

IS E.S. MODULE

RELEVANT APPARATUS

WITH INTRINSIC FUNCTION

TO END USER (CEMEP

VALIDITY FIELD 1)

YES

FIT THE SPECIFIED

E.S. EMC FILTER

WILL THE E.S. PRODUCT

BE INSTALLED

ACCORDING TO THE

INSTALLATION

GUIDELINES

YES

E.S. = ELETTRONICA SANTERNO

EMC 'CE' MARK CAN BE APPLIED TO E.S.

MODULE TO GENERIC EMC STANDARDS:

EN50081-1(1992), EN50081-2(1994) AND

EN50082-1(1992) (AND EN50082-2(1992)).

EMC CHARACTERISTICS

STATED IN MANUAL

OPTIONAL E.S. FILTERS

AVAILABLE TO ASSIST USERS

IN CONFORMANCE WITH THE

EMC DIRECTIVE

EMC INSTALLATION GUIDELINES

STATED IN MANUAL

CEMEP VALIDITY FIELDS

2, 3 AND 4

NO EMC 'CE' MARK APPLIED TO E.S. MODULE.

A GLOBAL EMC SOLUTION

MAY BE ADVANTAGEOUS

MANUFACTURER/SUPPLIER/INSTALLERS

RESPONSIBILITY TO CONFORM WITH EMC DIRECTIVE.

E.S. EMC CHARACTERISTICS AND MANUFACTURERS

IN THE OVERALL PRODUCT JUSTIFICATION

RELEVANT APPARATUS

THE E.S. DECLARATION OF CONFORMITY

FOR EMC IS VALID FOR THE SPECIFIED

MODULE WHEN INSTALLED CORRECTLY

DECLARATION MAY BE USED AS A BASIS

CEMEP = Refer to Chapter 4: "European Directives and the CE Mark”

Figure 12-

Figure 12-1

1 Elettronica Santerno EMC 'CE' Mark Validity Chart

Elettronica Santerno EMC 'CE' Mark Validity Chart

Содержание SINUS/ISD 200 S-0.75















































































































































































































Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы:

Elettronica Santerno SINUS/ISD 200 S-0.75, Руководство пользователя, Страница: 176 / 206

Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы: