Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 175

Страница: 175 / 206

SINUS/ISD

15P0082B8

USER MANUAL

12 - 3/8

12.1.5

WHICH STANDARDS APPLY?

12.1.5.1

Basic and Generic Standards

The standards that may apply to this unit come under two broad categories:

Emission - these standards limit the interference caused by operating (this) drive module.

Immunity - these standards limit the effect of interference (on this unit) from other electrical and electronic
apparatus.

The following table indicates the standards that the unit may comply with, dependent upon how it is installed and
used.

Unit used a

Relevant Apparatus

Unit used a

Component

Assuming installation to EMC instructions in this manual
“filter” refers to an internal ac supply EMC filter.

filter

(EMC

compliance)

no filter

filter

(EMC

compliance

may be

applied for)

no filter

Installation

Basic and Generic Standards

encl

Radiated RF Emission

EN55022 Class B (1994)
or
EN50081-1 (1992)

✓

Conducted RF Emission

EN55022 Class B (1994)
or
EN50081-1 (1992)

✓

Residential

Immunity

EN50081-1 (1992)

✓

Radiated RF Emission

EN55022 Class B (1994)
or
EN50081-1 (1992)

✓

Conducted RF Emission

EN55022 Class B (1994)
or
EN50081-1 (1992)

✓

Commercial
& Light
Industry

Immunity

EN50081-1 (1992)

✓

Radiated RF Emission

EN55011 Class A (1991)
or
EN50081-2 (1994)

✓

Conducted RF Emission

EN55011 Class A (1991)
or
EN50081-2 (1994)

✓

Industrial

Immunity

prEN50082-2 (1992)

✓

Table 12-

Table 12-1

1 Applicable Basic and Generic Standards

Applicable Basic and Generic Standards

Содержание SINUS/ISD 200 S-0.75















































































































































































































Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы:

Elettronica Santerno SINUS/ISD 200 S-0.75, Руководство пользователя, Страница: 175 / 206

Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы: