Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 206

Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 49

SINUS/ISD

15P0082B8

USER MANUAL

5 - 7/14

5.4.4

ALERT MESSAGE DISPLAYS

A message will be displayed on the Operator Station when either:

•

A requested operation is not allowed.

The top line details the illegal operation, while the bottom line gives the
reason or cause. See example opposite.

•

The Inverter has tripped.

The top line indicates a trip has occurred while the bottom line gives
the reason for the trip. See example opposite.

Most messages are displayed for only a short period, or for as long as an illegal operation is tried, however, trip
messages must be acknowledged by pressing the E

E key.

Experience will show how to avoid most messages. They are displayed in clear, concise language for easy
interpretation. Refer to Chapter 7: “Trips and Fault Finding” for trip messages and reasons.

5.4.5 THE PROG KEY

The PROG

PROG key toggles between the OPERATOR menu and any other menu, remembering and returning to

previous positions in each menu. As you press the PROG

PROG key, the title of the menu you are about to enter is

displayed, i.e. OPERATOR or for example TRIPS. Releasing the key clears the display and releases you into
that menu.

WELCOME SCREEN

OPERATOR

PROG

The Menu System

M

E

SETPOINT (REMOTE)

to other parameters

to other menus/parameters

press immediately after
power-up to skip the
timeout

timeout

from

power-up

Figure 5-

Figure 5-3

3 The Menu System showing Operation of the E, M and PROG Keys

The Menu System showing Operation of the E, M and PROG Keys

5.4.6 THE L/R KEY

The L/R

L/R key (LOCAL/REMOTE) toggles between Remote and Local Control. In doing so, the view of the

SETPOINT parameter in the OPERATOR menu toggles between LOCAL SETPOINT and REMOTE SETPOINT.
The default is for the REMOTE SETPOINT parameter to be displayed.

Note:

A different naming convention is applied in the OPERATOR menu for these parameters when displayed
as the first parameter entry:

•

REMOTE SETPOINT is displayed as SETPOINT (REMOTE)

•

LOCAL SETPOINT is displayed as SETPOINT (LOCAL)

Pressing the L/R key when in Remote mode takes you directly to the SETPOINT (LOCAL) parameter with the
Edit mode enabled. Press the PROG key to return to the previous display.

HEALTH

LOCAL

SEQ

REF

1

1

REMOTE SEQ

* KEY INACTIVE *

HEALTH

LOCAL

SEQ

REF

1

1

HEATSINK TEMP

* * * TRIPPED * * *

«
...
47
48
49
50
51
...
»

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов