Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 206

Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 119

SINUS/ISD

15P0082B8

USER MANUAL

6 - 63/82

6.4.1.41

STOP

This function block holds all the
parameters concerning the stopping
method of the inverter.
The stopping methods of the inverter
are described in more detail in Chapter
4: “Operating the Inverter” - Starting and
Stopping Methods..

MMI Menu Map

1

SETUP PARAMETERS

2

FUNCTION BLOCKS

3

SEQ & REF

4

STOP

RUN STOP MODE

STOP RATE

STOP ZERO SPEED

STOP DELAY

FAST STOP MODE

FAST STOP LIMIT

FAST STOP RATE

FINAL STOP RATE

STOP

STOP

RAMPED – [279] RUN STOP MODE

––

10.0 s –– [263] STOP RATE

––

0.10 % –– [266] STOP ZERO SPEED ––

0.500 s –– [284] STOP DELAY

––

RAMPED –– [304] FAST STOP MODE ––

30.0 s –– [275] FAST STOP LIMIT

––

0.1 s –– [264] FAST STOP RATE

––

1200 Hz/s

–

[126] FINAL STOP RATE

–

Parameter Descriptions

Parameter Descriptions

RUN STOP MODE

RUN STOP MODE

Range: Enumerated - see below

Selects stopping mode that the controller will use once the run command has been
removed. The choices are:

Enumerated Value

:

Stopping Mode

0 : RAMPED
1 : COAST
2 : DC INJECTION

When RAMPED is selected, the inverter will decelerate using the system ramp
deceleration time, provided it is non zero. When COAST is selected, the motor will free-
wheel. When DC INJECTION is selected, the motor is stopped by applying dc current.
STOP RATE

STOP RATE

Range: 0.0 to 600.0 s

Rate at which the demand is ramped to zero after the ramp has been quenched.
STOP ZERO SPEED

STOP ZERO SPEED

Range: 0.00 to 100.00 %

Threshold for zero speed detection used by stop sequences.
STOP DELAY

STOP DELAY

Range: 0.000 to 30.000 s

Sets the time at which the inverter holds zero speed before quenching after a normal
stop or a jog stop. This may be particularly useful if a mechanical brake requires time to
operate at zero speed, or for jogging a machine to position.
FAST STOP MODE

FAST STOP MODE

Range: Enumerated - see below

Selects stopping mode used during a fast stop, two options ramped or coast.

Enumerated Value

:

Stopping Mode

0 : RAMPED
1 : COAST

FAST STOP LIMIT

FAST STOP LIMIT

Range: 0.0 to 3000.0 s

Maximum time that the inverter will try to Fast Stop, before quenching.
FAST STOP RATE

FAST STOP RATE

Range: 0.0 to 600.0 s

Rate at which the SPEED DEMAND is ramped to zero (see REFERENCE function
block)
FINAL STOP RATE

FINAL STOP RATE

Range: 12 to 4800 Hz/s

Rate at which any internally generated setpoint trims are removed. For example, the trim
due to the slip compensation block.

«
...
117
118
119
120
121
...
»

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов