manualshive.com logo in svg

Elettronica Santerno SINUS/ISD 200 S-0.75, Руководство пользователя, Страница: 46 / 206

Поделиться
Скачать
Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 46

15P0082B8

USER MANUAL

SINUS/ISD

5 - 4/14

5.4

5.4

 

THE MENU SYSTEM

THE MENU SYSTEM

The menu system is divided into a `tree’ structure with 5 menu levels. Menu Level 1 is at the top of the tree.
Parameters contained in Menu Level 1 are the most frequently used, as you descend the menu levels the
parameters are less frequently used.

The Operator Station has selectable “viewing levels” which can restrict the view of the menu system, refer to
“ Menu Viewing Levels”, page 5-9/14.

Below is a simple description of the menus at Menu Level 1:

•

 

OPERATOR: a view of selected parameters contained in the FUNCTION
BLOCKS menu. You can customise the Operator menu to create a working list
of parameters for operating your Inverter.

•

 

DIAGNOSTICS: a view of important diagnostic parameters contained in the
FUNCTION BLOCKS menu.

•

 

SETUP PARAMETERS: contains all the function block parameters for
programming your application, including  parameters for tuning the Inverter.

•

 

PASSWORD: a view of  important Password parameters contained in the
FUNCTION BLOCKS menu.

•

 

TRIPS STATUS: a view of the trip diagnostic parameters contained in the
FUNCTION BLOCKS menu.

•

 

MENUS: a view of parameters contained in the FUNCTION BLOCKS menu for
setting-up the Operator Station display.

•

 

PARAMETER SAVE: Save the application.

•

 

SYSTEM: contains all the parameters for the internal workings of the Operator
Station, including Macro selection.

Figure 5-

Figure 5-2

2  The Menu System showing Menus at Level 1

  The Menu System showing Menus at Level 1

5.4.1

 

 NAVIGATING THE MENU SYSTEM

On power-up, the Operator Station defaults into the OPERATOR menu, timing out from the Welcome screen.
You can skip the timeout by pressing the M

M key immediately after power-up which will take you directly to the

OPERATOR menu.

The menu system can be thought of as map which is navigated using
the four keys shown opposite.

Keys E

 E and M

M navigate through the menu levels.

The up  

(

∆∆

)

 and down 

(

∇

∇

) 

keys scroll through the Menu and Parameter

lists.

Refer to  “

Refer to  “  The Programmer Menu System Map

  The Programmer Menu System Map” to see how the

” to see how the

menu is mapped.

menu is mapped.

HINT: 

HINT: Remember that because the Menu and Parameter lists are looped, the 

∆

 key can quickly move you to the

last Menu or Parameter in the loop.

WELCOME SCREEN

OPERATOR

The Menu System

timeout

from

power-up

DIAGNOSTICS

SETUP PARAMETERS

PASSWORD

TRIPS STATUS

MENUS

PARAMETER SAVE

SYSTEM

menu at level 1

menu at level 1

menu at level 1

menu at level 1

menu at level 1

menu at level 1

menu at level 1

menu at level 1

scroll

scroll

exit to

previous

menu

next menu

NAVIGATING THE MENU

E

M

Содержание SINUS/ISD 200 S-0.75















































































































































































































Отзывы:

Нет отзывов