Elettronica Santerno SINUS/ISD 200 S-0.75 Скачать руководство пользователя страница 1

Страница: 1 / 206

USER MANUAL

•

This manual is integrant and essential to the product. Carefully read the instructions contained herein as they

provide important hints for use and maintenance safety.

•

This device is to be used only for the purposes it has been designed to. Other uses should be considered

improper and dangerous. The manufacturer is not responsible for possible damages caused by improper,
erroneous and irrational uses.

•

Elettronica Santerno is responsible for the device in its original setting.

•

Any changes to the structure or operating cycle of the device must be performed or authorized by the

Engineering Department of Elettronica Santerno.

•

Elettronica Santerno assumes no responsibility for the consequences resulting by the use of non original spare-

parts.

•

Elettronica Santerno reserves the right to make any technical changes to this manual and to the device without

prior notice. If printing errors or similar are detected, the corrections will be included in the new releases of the
manual.

•

Elettronica Santerno is responsible for the information contained in the original version of the Italian manual.

•

The information contained herein is the property of Elettronica Santerno and cannot be reproduced. Elettronica

Santerno enforces its rights on the drawings and catalogues according to the law.

Elettronica Santerno

Elettronica Santerno S.p.A.

S.p.A.

Via G. Di Vittorio, 3 - 40020 Casalfiumanese (Bo) Italy

Tel. +39 542 668611 - Fax +39 542 666632

After Sales Service Tel. +39 542 668610 - Fax +39 542 666778

Sales Office Tel. +39 51 6010231 - Fax +39 51 534403

••

15P0082B8

••

SINUS/ISD 0.75

÷÷

4 kW

VECTORIAL SENSORLESS INVERTER

VERS. 4.x

R. 0.1

(EXTENDED MANUAL)

UPD. 15/03/99

E n g l i s h

Содержание SINUS/ISD 200 S-0.75















































































































































































































Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы:

Elettronica Santerno SINUS/ISD 200 S-0.75, Руководство пользователя, Страница: 1 / 206

Результаты поиска

Содержание SINUS/ISD 200 S-0.75

Отзывы: