background image

54

Speed Bake 

times, start with a 30% reduction in

time and increase the time until the desired
doneness is obtained. Time reductions will vary
depending on the amount and type of food.

2. Preheating is not necessary when cooking with

Speed Bake

, except with items such as cakes,

cookies, biscuits, breads, etc.

3. When using two racks at the same time, place in

positions 2 and 5 for the best results.

4. Layer cakes and similar food items will have better

results when baked with the normal bake function.

To Set Speed Bake™ Cooking System:

1. Program the oven as you normally would for

baking. Speed Bake may be used with Bake, Time
Bake and Delayed Time Bake features.

2.

Press and release 

Speed Bake

 switch. The

indicator light will glow and the fan will come on
after a 

6 MINUTE DELAY

. If the oven temperature

has already reached 

350°F

, the fan will come on

immediately.The fan stays on when the oven door
is closed and shuts off while the oven door is
opened. The fan will continue to operate until
baking is complete.

3. To cancel the Speed Bake function, press 

Clear

Off 

on the oven control as you would to cancel any

baking function.

NOTE:

The Speed Bake feature will not work during a
clean cycle.

NOTE:

In the Speed Bake feature, the oven cannot be
set lower than 250°F.

To Broil:

1. Arrange oven rack while oven is still cool. Position

the rack as suggested in the chart below.

Rack Position From Top

Food

1

Rare steaks

2

Fish, medium steaks,
hamburgers, chops

3

Well-done foods such
as chicken and lobster

2. Press

 Broil.

3. Press and hold the 

Up Arrow

 

or Down Arrow

 until

the desired broil setting level appears in the display.
Press the 

Up Arrow

 for 

HI

 broil or the 

Down Arrow

for

 LO

 broil. Most foods can be broiled at the 

HI

 broil

setting. Select the 

LO

 broil setting to avoid excess

browning or drying of foods that should be broiled to
the well-done stage.

4. Place the insert on the broiler pan, then place the

food on the insert. 

DO NOT

 use the broiler pan

without the insert or cover the insert with aluminum
foil. The exposed grease could ignite.

5. Place the pan on the oven rack. 

Open the oven

door to the broil stop position when broiling

.

6. Broil on one side until food is browned; turn and

cook on the second side. 

Note:

 Always pull the

rack out to the stop position before turning or
removing food.

7. When broiling is finished, press 

Clear Off.

CAUTION:

 Should an oven fire occur, close the oven

door and turn off the oven. If the fire continues, use a
fire extinguisher. 

DO NOT

 put water or flour on the fire.

Flour may be explosive.

SELF-CLEANING OVEN

A self-cleaning oven cleans itself with high temperatures
(well above cooking temperatures) which eliminate
soil completely or reduce it to a fine powdered ash you
can wipe away with a damp cloth.

Adhere to the following cleaning precautions:

DO NOT 

use oven cleaners or oven protective

coatings in or around any part of the self-cleaning
oven.

DO NOT

 clean the oven door gasket. The woven

material of the oven door gasket is essential for a
good seal. Care should be taken not to rub, damage
or remove the gasket.

DO NOT

 use any cleaning materials on the oven

door gasket. Doing so could cause damage.

Remove the broiler pan and insert, all utensils
and any aluminum foil. These items cannot
withstand high cleaning temperatures.

Oven racks may be left in the oven or may be
removed. If they go through the clean cycle their
color will turn slightly blue and the finish will be dull.
After the cycle is complete and the oven has cooled,

Содержание 30" GAS FREESTANDING RANGES





































































































































Отзывы: