manualshive.com logo in svg

Electro-Music Klee Sequencer, Инструкция по сборке, Страница: 71 / 120

Поделиться
Скачать
Electro-Music Klee Sequencer Скачать руководство пользователя страница 71

7.

 

Building The Boards 

 
 
 

The 

electro-music

 Klee Sequencer PCB Set 

 

The PCB set consists of two boards, as the word “set” would seem to indicate.  One 
board, with the bulk of the analog functions is labeled the “Analogue Board”.  The 
other board, which contains the bulk of the digital functions, is called the “Digital 
Board”. 
 
The two boards interconnect between each other, the power supply, and the front 
panel to form the 

electro-music

 Klee Sequencer.  Before you start slapping parts on 

them and jamming solder onto the leads, you should first read at least this first section 
so that you know which parts you want to slap onto the boards and jam solder onto 
the leads.  Remember – there are a couple of options that will determine what goes in 
and what stays out. 
 

Digital Board Parts Considerations 

The Digital Board is fairly straightforward as to which parts are installed onto it.  The 
only section that makes a difference would be the gate bus resistors.  These resistors 
determine the output level of the gate and trigger signals the Klee will produce.  You, 
the builder and owner of the Klee may have a preference as to these levels.  The Klee 
will produce either 5V range gate and trigger signals or 10V range gate and trigger 
signals.  The values used for these resistors will determine what gate/trigger voltages 
you end up with.  There are no jumper wires that need be installed on the Digital 
Board. 
 

Analogue Board Parts Considerations 

The Analogue Board is the board involved with the Variable Range options discussed 
throughout this text.  If you have decided not to include any of the variable range 
options in your Klee, then you will need to install all of the trim pots and a jumper.  
There is a connector that need not be installed, as well as a diode. 
 
If you have decided to include any of the Variable Range options, there is a jumper 
that is 

not

 installed, a trim pot that is 

not

 installed, and a connector and diode that 

are

 

installed. 
 
In addition to the Variable Range Option consideration, another jumper is installed or 
not, depending on if your power supply has one or two ground connections available. 
 
That’s it for the planning stages – let’s get to putting those boards together! 
 
 
 

 

69

Содержание Klee Sequencer

























































































































Отзывы:

Нет отзывов