manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Руководство по установке и эксплуатации, Страница: 81 / 322

Поделиться
Скачать
Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 81

     

Doc

#    

E154713     

                              

              4-9

4: Electrical Installation

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

4.5.1: Voltage Inputs

Select a wiring diagram from Section 4.6 that best suits your application and wire the 
meter exactly as shown. For proper operation, the voltage connection must be main-
tained and must correspond to the correct terminal. Program the PT ratios in the 

Device Profile section of the Communicator EXT

TM

 software; see the 

Communicator 

EXT

TM

 4.0 and MeterManager EXT Software User Manual

 for details.

4.5.1.1: Wiring the Voltage Inputs

•  The cable required to terminate the voltage sense circuit should have an insulation 

rating greater than 600VAC and a current rating greater than 0.1A.

•  Wire type: Solid or stranded

•  Wire gauge: 12-24 AWG for either solid or stranded wire

•  Strip length: 7-8mm

•  Torque: 5 Lb-In

4.5.1.2: Fusing the Voltage Connections

•  For accuracy of the readings and for protection, EIG requires using 0.1 Amp rated 

fuses on all voltage inputs.

•  The Nexus® 1500+ meter allows measurement up to a nominal 347VAC phase to 

neutral and up to 600VAC phase to phase. Potential Transformers (PTs) are 
required for higher voltages to insure proper safety. 

•  Use a 4 Amp Slo-Blo fuse on the power supply for control power, for example, UL 

approved Littelfuse part number FLQ4.

4.5.2: Wiring the Vaux Input 

The voltage auxiliary (Vaux) connection is an auxiliary voltage input that can be used 
for any desired purpose, such as monitoring two different lines on a switch. The VAux 
voltage rating is the same as the metering voltage input connections.

4.5.3: Ground Connections

The meter's PE GND terminal should be connected directly to the installation's protec-

tive earth ground. Use AWG#12/2.5mm

2

 wire for this connection.

Содержание Shark 100T



































































































































































































































































































































Отзывы:

Нет отзывов