Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 322

Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 78

Doc

#

E154713

4-6

4: Electrical Installation

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

4.3: Installing Current Transformer Sensors with No Meter

Termination (Pass Through)

The second method allows the CT wires to pass through the CT inputs without
terminating at the meter. In this case, remove the current gills and place the CT wire
directly through the CT opening. The opening accommodates up to 0.177"/4.5mm
maximum diameter CT wire.

Figure 4.2: Pass Through Wire Electrical Connection

NOTE:

For sustained loads greater than 10 A, use 10 AWG wire.

CT wire
passing

through
meter
with

current

gills
removed

Close-up of CT

openings

«
...
76
77
78
79
80
...
»

Содержание Shark 100T



































































































































































































































































































































Отзывы:

Нет отзывов