Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 322

Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 75

Doc

#

E154713

4-3

4: Electrical Installation

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

endommagements de transformateur de courant si l'unité Nexus 1500+ doit être
enlevée du service. Un côté du transformateur de courant doit être mis à terre.

NOTE

: Les entrées actuelles doivent seulement être branchées dans le transforma-

teur externe actuel par l'installateur. Le transformateur de courant doit être approuvé
ou certifié et déterminé pour le compteur actuel utilisé.

La taille de la protection de la dérivation doit être de 15 ampères.

Pour les charges continues de plus de 10 ampères, les fils des transformateurs de
courant doivent être câblés directement à travers l'ouverture pour les transformateurs
de courant (la méthode de câblage de passage - voir Section 4.3), à l'aide de fils de
calibre américain des fils de 10.

IF THE EQUIPMENT IS USED IN A MANNER NOT SPECIFIED BY THE
MANUFACTURER, THE PROTECTION PROVIDED BY THE EQUIPMENT
MAY BE IMPAIRED.

THERE IS NO REQUIRED PREVENTIVE MAINTENANCE OR INSPECTION NECESSARY
FOR SAFETY. HOWEVER, ANY REPAIR OR MAINTENANCE SHOULD BE PERFORMED BY
THE FACTORY.

DISCONNECT DEVICE: The following part is considered the equipment
disconnect device. A SWITCH OR CIRCUIT-BREAKER SHALL BE
INCLUDED IN THE END-USE EQUIPMENT OR BUILDING
INSTALLATION. THE SWITCH SHALL BE IN CLOSE PROXIMITY TO THE
EQUIPMENT AND WITHIN EASY REACH OF THE OPERATOR. THE

SWITCH SHALL BE MARKED AS THE DISCONNECTING DEVICE FOR
THE EQUIPMENT.

IMPORTANT! SI L'ÉQUIPEMENT EST UTILISÉ D'UNE FAÇON NON
SPÉCIFIÉE PAR LE FABRICANT, LA PROTECTION FOURNIE PAR L'ÉQUI-
PEMENT PEUT ÊTRE ENDOMMAGÉE.

«
...
73
74
75
76
77
...
»

Содержание Shark 100T



































































































































































































































































































































Отзывы:

Нет отзывов