Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 151

Страница: 151 / 322

Doc

E154713

9-1

9: Network Communications

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

9: Network Communications

9.1: Hardware Overview

The Nexus® 1500+ meter can connect to multiple PCs via Modbus/TCP over the
Ethernet or via a DNP LAN/WAN connection.

Figure 9.1: Nexus® 1500+ Meter Connected to Network

The Nexus® 1500+ meter's Network is an extremely versatile communications tool.
It:

• Adheres to the IEEE 802.3 Ethernet standard using Modbus TCP/IP.

• Utilizes simple and inexpensive 10/100BaseT wiring and connections.

• Plugs into your network using built-in RJ45 jack.

• Is programmable to any IP address, subnet mask and gateway requirements.

• Communicates using the industry-standard Modbus/TCP and DNP LAN/WAN

protocols, and with V-Switch

Key 2 and above, IEC 61850 Protocol. It also

supports SNMP (see Appendix D: Using SNMP, on page D-1).

Содержание Shark 100T



































































































































































































































































































































Результаты поиска

Содержание Shark 100T

Отзывы:

Electro Industries/GaugeTech Shark 100T, Руководство по установке и эксплуатации, Страница: 151 / 322

Результаты поиска

Содержание Shark 100T

Отзывы: