Eldes ESIM264, Руководство по установке

Страница: 51 / 60

100 101 100 101 EN EN MANUAL ELDES ESIM264 V3.2 MANUAL ELDES ESIM264 V3.2
Delete monitoring
station phone number
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST →
OK → TEL. NUMBER 1... 3 → OK → OK
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s Tel Number 1 via Voice Calls or SMS method is unsuccessful, the
system will make up to 4 additional attempts. After all unsuccessful attempts, the system will continue to communicate with the monitor-
ing station by switching to the next phone number that follows in the sequence and making up to 4 additional attempts if the initial at-
tempt is unsuccessful. If all attempts to all phone numbers are unsuccessful, the system will switch to next backup connection that follows
in the sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
MS SETTINGS
→
OK
→
VOICE CALLS/SMS ST
→
OK
→
ATTEMPTS
→
OK
→
at
→
OK
Value: aaaa – 4-digit administrator password; at – number of attempts, range – [1... 10].
EKB3
Enter parameter 37 and number of attempts:
37 at #
Value: at – number of attempts, range – [01... 10].
Example: 3706#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Due to the individual configuration of each monitoring station, the system may fail to deliver the data message via Voice Calls communi-
cation method. In such cases it is recommended to adjust the microphone gain until the optimal value, leading to successful data message
delivery, is discovered.
Set microphone gain
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK
→ MICROPHONE GAIN → OK → mg → OK
Value: aaaa – 4-digit administrator password; mg – microphone gain, range – [0... 15].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
30.2.3. CSD
The system supports up to 5 monitoring station phone numbers for communication with the alarm system by CSD communication method.
Tel. Number 1 is mandatory, the other four can be used as backup phone numbers and are not necessary. The supported phone number
format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format:
[international code][area code][local number], example for UK: 44170911XXXX1 .
To set up the system for data transmission via CSD, please follow the basic configuration steps:
1. Enable MS Mode parameter (see
30. MONITORING STATION ).
2. Set 4-digit Account number (see 30. MONITORING STATION ).
3. Set Tel. Number 1... 5.
Set monitoring station
phone number
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5 → OK → ttteeellnnuumm → OK
Value: aaaa – 4-digit administrator password; ttteeellnnuumm – up to 15 digits monitoring
station phone number.
EKB3
Enter parameter 85, number of entry and phone number:
85 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 05]; ttteeellnnuumm – up to 15 digits monitor-
ing station phone number.
Example: 85014417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Delete monitoring
station phone number
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5
→
OK
→
OK
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s phone number via CSD method is unsuccessful, the system will
make up to 4 additional attempts. If all attempts are unsuccessful, the system will switch to next backup connection that follows in the
sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5
→
OK
→
OK
Value: aaaa – 4-digit administrator password; at – number of attempts, range – [1... 10].
EKB3
Enter parameter 84 and number of attempts:
84 at #
Value: at – number of attempts, range – [01... 10].
Example: 8403#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.