background image

22

23

22

23

EN

EN

MANUAL ELDES ESIM264 V3.2

MANUAL ELDES ESIM264 V3.2

4. GENERAL OPERATIONAL DESCRIPTION 

When the system is being armed, it will initiate the exit delay countdown intended for the user to leave the secured area. During the 

countdown period the buzzer will emit short beeps and/or LED indicator will flash. By default, exit delay duration is 15 seconds. After the 

countdown is complete, the system will become armed and lock the configuration by keypad possibility. In case the user does not leave the 

secured area before the countdown is complete, the system will arm in Stay mode if at least 1 zone has Stay attribute enabled. By default, 

if there is at least 1 violated zone or tamper, the user will not be able to arm the system until the violated zone or tamper is restored. In case 

it is required to arm the alarm system despite the violated zone presence, the violated zone can be bypassed or Force attribute enabled.

After the system is armed and if a zone (depending on type) or tamper is violated, the system will cause an alarm lasting for 1 minute (by 

default), During the alarm, the siren/bell will provide an alarm sound along with the buzzers of the keypads. By default, the system will also 

makes a phone call and send an SMS text message containing the violated zone or tamper number to a listed user and indicate the violated 

zone or tamper number on the keypad. If another zone or tamper is violated or the same one is restored and violated again during the alarm, 

the system will act as mentioned previously, but will not extend the alarm time.

After the user enters the secured area, the system will initiate the entry delay countdown intended for system disarming. During the count-

down period, the buzzer will emit a steady beep and/or LED indicator will light ON. By default, entry delay duration is 15 seconds. After the 

user successfully performs the disarming process, the system will unlock the keypads. If the user does not disarm the system in time, the 

alarm system will cause an  instant alarm.

NOTE: 

  The alarm will be caused even if a tamper is violated while the system is disarmed.

For more details, please refer to 

12. ARMING AND DISARMING

.

5. CONFIGURATION METHODS

!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character must 

be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning and at 

the end of the SMS text message.  

5.1.  SMS Text Messages 

SMS

In order to configure and control the system by SMS text message, send the text command to the ESIM264 system phone 

number from one of the listed user phone numbers. The structure of SMS text message consists of 4-digit SMS password 

(the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g. 

STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in 

5.2.  EKB2 LCD Keypad

EKB2

The system configuration and control by EKB2 keypad is carried out by navigating throughout the menu section list displayed 

on LCD screen. To navigate in the menu path, touch 

 keys to select the desired menu section and touch OK key to open the 

selected section. To enter a required value, use 0... 9 keys and touch OK key for confirmation or cancel/go one menu section 

back by touching 

 key. The value can be typed in directly by touching 0... 9 keys while highlighting the desired menu sec-

tion. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will be brought back to the 

beginning of the list after touching the 

 key. In this installation manual, the menu path is based on the EKB2 menu tree by 

starting at home screen view (see 

31.1.1.6. EKB2 Menu Tree   

). The variables are provided in lower-case letters, while a valid 

parameter value range is provided in brackets.

NOTE: 

  Menu section CONFIGURATION is secured with administrator password. The default administrator password is 

1470

NOTE: 

  The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the menu section 

CONFIGURATION is opened. The inactive EKB2 keypads will display   icon and 

CONFIGURATION

 

MODE

 message.

NOTE: 

  The keypad will automatically exit the menu section CONFIGURATION and return to home screen view if 1 minute after the last 

key-touch expires.

5.3.  EKB3 LED Keypad

EKB3

The system configuration and control by EKB3 keypad is carried out by activating the Configuration mode using the adminis-

trator password (by default – administrator password is 

1470

) and entering a valid configuration command using the number 

keys [0]... [9], [#] key for confirmation and [*] key to cancel the characters that are being entered. Alternatively, the user 

can wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the entered characters have been 

cancelled. When typing in the characters, the indication of each pressed key is provided by short beep of keypad buzzer and 

red indicators when the number keys [0]... [9] are being pressed.  Some commands require [BYPS], [CODE] and [STAY] keys as 

well. The structure of a standard configuration command is a combination of digits. The commands, which do not require the 

Configuration mode being activated, are noted. The variables are provided in lower-case letters, while a valid parameter value 

range is provided in brackets.

NOTE: 

  If you were not willing to activate Configuration mode, but accidentally typed in the * as the first character, please press [*] key again 

or wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the typed in characters have been cancelled. 

Activate/deactivate 

Configuration mode

EKB3

Enter administrator password:

* aaaa #

Value:

 

aaaa

 – 4-digit administrator password.

Example: 

*1470#

The following table provides a list of EKB3 indications, which are relevant during Configuration mode.

Indication

Description

Indicator ARMED flashing

Configuration mode activated successfully.

Indicator SYSTEM flashing

Valid parameter is entered and waiting for valid value to be entered.

1 long beep

Non-existing command or invalid parameter value entered.

3 short beeps

Command entered successfully.

NOTE: 

  The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the Configura-

tion mode is activated.

NOTE: 

  Configuration mode will automatically deactivate if 1 minute after the last key-stroke expires.

Содержание ESIM264





























































Отзывы: