Eldes ESIM264, Руководство по установке

Страница: 22 / 60

42 43 42 43 EN EN MANUAL ELDES ESIM264 V3.2 MANUAL ELDES ESIM264 V3.2
Set entry delay for
Delay zone
SMS
SMS text message content:
ssss_ENTRYDELAY:nn,eeeee or ssss_ENTRYDELAY:nn,eeeee;nn,eeeee;nn,eeeee;nn,eeeee
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 44], eeeee – entry delay
duration, range – [0... 65535] seconds.
Example: 1111_ENTRYDELAY:1,25;14,32;12,20
EKB2
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK →
ONBOARD ZONES → OK → ZONE 1... 12 → OK → ENTRY DELAY → OK → eeeee → OK
Wireless zone: OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
ZONES
→
OK
→
WIRELESS
ZONES
→
OK
→
WLESS ZONE 1... 16
→
OK
→
ENTRY DELAY
→
OK
→
eeeee
→
OK
Keypad zone: OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
ZONES
→
OK
→
KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → ENTRY DELAY → OK → eeeee → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → ENTRY DELAY → OK → eeeee → OK
Value: aaaa – 4-digit administrator password; eeeee – entry delay duration, range – [0...
65535] seconds.
EKB3
Enter parameter 54, partition number and entry delay duration:
54 nn eeeee #
Value: nn – zone number, range – [01... 44], eeeee – entry delay duration, range – [0... 65535]
seconds
Example: 5403259#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on zone types, please refer to 14.5. Zone Type Definitions .
14. ZONES
Detection devices such as motion detectors and door contacts are connected to the alarm system’s zone terminals. Once connected, the
associated zone’s parameters must be configured.
ESIM264 comes equipped with 6 on-board zones allowing to connect up to 6 detection devices. For more details regarding zone expansion,
please refer to 14.2. Zone Expansion .
ESIM264 zones are classified by 5 categories:
Zone category Description
Max. number of
zones per device
Max. number of
zones in total
On-board zones Built-in wired zones of ESIM264 alarm system. 6/12* 6/12*
Keypad zones Hardwired zones of EKB2/EKB3 keypad. 1 4
EPGM1 zones Zones of EPGM1 - hardwired zone and PGM output expan-
sion module.
16 16
Wireless zones Non-physical zones automatically created by connected
wireless devices.
4** 32***
Virtual zones Non-physical zones intended for Panic button feature (alarm
activation upon pressing the button) on EWK1/EWK2 wire-
less keyfob. Virtual zones can be manually created using EL-
DES Configuration Tool software.
32**** 32****
* - 6-Zone mode is enabled by default. ATZ mode doubles the on-board zone number and increases it to 12 in total.
** - Depends on the connected wireless device.
*** - Available only if no keypad zones, EPGM1 zones and virtual zones are present.
**** - Available only if no keypad zones, EPGM1 zones and wireless zones are present.
14.1. Zone Numbering
The zone numbers ranging from Z1 through Z12 are permanently reserved for on-board zones even when ATZ mode is disabled. The
Z13-Z44 zone numbers are automatically assigned in the chronological order to the created virtual zones and the devices connected to the
system: keypads, wireless devices, EPGM1 modules.
14.2. Zone Expansion
For additional detection device connection, the number of zones can be expanded by:
• enabling the ATZ (Advanced Technology zone) mode (see 14.4. ATZ (Advanced Technology Zone) Mode ).
• connecting EPGM1 hardwired zone and PGM output expansion module (for more details on technical specifications and installation,
please refer to the latest user manual of the device located at www.eldes.lt/download).
• connecting keypads (see 31.1.1. EKB2 – LCD Keypad and 31.1.2. EKB3 – LED Keypad ).
• pairing wireless devices (see 19. WIRELESS DEVICES ).
• creating virtual zones (see ELDES Configuration Tool software’s Help section).
The maximum supported number of zones is 44.
14.3. 6-Zone Mode
By default, ESIM264 alarm system runs in the 6-Zone mode under zone connection Type 1 allowing to connect up to 6 detection devices of
NO (normally-open) type to the on-board zone terminals as indicated in the wiring diagram of Type 1. Once a different zone connection type
is set, the detection device wiring must be done according to the wiring diagram of the associated type.
Available zone connection types for the 6-Zone mode:
• Type 1 – Parallel wiring of NO (normally-open) detection device with 5,6kΩ EOL (end-of-line) resistor.
• Type 2 – Serial wiring of NC (normally-closed) detection device with 5,6kΩ EOL resistor.
• Type 3 – Combination of serial and parallel wiring of tamper with 5,6kΩ EOL resistor and NC (normally-closed) detection device with
3,3kΩ EOL resistor.