Eldes ESIM264, Руководство по установке

Страница: 45 / 60

88 89 88 89 EN EN MANUAL ELDES ESIM264 V3.2 MANUAL ELDES ESIM264 V3.2
ATTENTION: The system will NOT send any data to the monitoring station while remote connection, remote firmware update or remote
listening/2-way voice communication is in progress. However, during the remote connection session or remote listening/2-way voice com-
munication process, the data messages will be queued up and transmitted to the monitoring station after the remote connection session or
remote listening/2-way voice communication process is over, while during the remote firmware update process NO data will be queued up
and all data messages will be lost.
ATTENTION: Phone calls to the listed user phone number in case of alarm are disabled by force when MS mode is enabled.
NOTE: Additional charges may apply for voice calls/data traffic based on your cell phone service plan when using the MS mode.
30.1. Data Messages – Events
The configuration of data messages is based on Ademco Contact ID protocol. The data messages can either be transmitted to the monitor-
ing station alone or with duplication by SMS text message to listed user phone number. For more details on system notifications by SMS text
message, please refer to 27. SYSTEM NOTIFICATIONS .
Seq. No. Contact ID® Code Event Description
1 1110 Fire alarm Transmitted in case a zone of Fire type is violated.
2 3110 Fire restore Transmitted in case a zone of Fire type is restored.
3 3121 Armed by user (Duress code) Transmitted in case the system is armed by Duress code.
4 1121 Disarmed by user (Duress
code)
Transmitted in case the system is disarmed by Duress code.
5 1130 Burglary alarm Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is violated.
6 3130 Burglary restore Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is restored.
7 1133 24-Hour zone alarm Transmitted in case of zone of 24-Hour type is violated.
8 3133 24-Hour zone restore Transmitted in case of zone of 24-Hour type is restored.
9 1144 Tamper alarm Transmitted in case the tamper is violated.
10 3144 Tamper restore Transmitted in case the tamper is restored.
11 1146 Panic/Silent zone alarm Transmitted in case of zone of Panic/Silent type is violated.
12 3146 Panic/Silent zone restore Transmitted in case of zone of Panic/Silent type is restored.
13 1158 Temperature risen Transmitted in case of the temperature has increased above the MAX set
value.
14 1159 Temperature fallen Transmitted in case of temperature has decreased below the MIN set value.
15 1301 Mains power loss Transmitted in case the mains power is lost.
16 3301 Mains power restore Transmitted in case the mains power is restored.
17 1302 Low battery Transmitted in case the backup battery voltage is 10.5V or lower / the
wireless sensor battery level runs below 5%.
18 1308 System shutdown When the system is running on backup battery power, it transmits the data
message before the backup battery power is fully depleted.
19 1309 Battery failed Transmitted in case the backup battery resistance is 2Ω or higher.
20 1358 GSM connection failed Transmitted in case the GSM connection is lost.
21 1381 Wireless signal loss Transmitted in case the connection with any wireless device is lost.
22 3381 Wireless signal restore Transmitted in case the connection with any wireless device is restored.
23 1401 Disarmed by user Transmitted in case the system is disarmed.
24 3401 Armed by user Transmitted in case the system is armed.
25 1456 Disarmed in Stay mode Transmitted in case the system is disarmed in Stay mode.
26 3456 Armed in Stay mode Transmitted in case the system is armed in Stay mode.
27 3463 SGS code entered Transmitted in case the SGS code is entered.
28 3602 Test event/Kronos ping Transmitted for system online status verification purposes.
29 3626 Date/time not set Transmitted in case system date and time is not set.
30 1900 System started Transmitted on system startup.
The following table refers to user codes included in arm/disarm data messages.
Type ID
User Phone Number 1 0
User Phone Number 2 1
User Phone Number 3 2
User Phone Number 4 3
User Phone Number 5 4
iButton 1 5
iButton 2 6
iButton 3 7
iButton 4 8
iButton 5 9
User Code 1 10
User Code 2 or Arm/Disarm by Zone 11
User Code 3 12
User Code 4 13
User Code 5 14
User Code 6 15
User Code 7 16
User Code 8 17
User Code 9 18
User Code 10 19
User Code 11 20
User Code 12 21
User Code 13 22
User Code 14 23
User Code 15 24
User Code 16 25
User Code 17 26
User Code 18 27
User Code 19 28
User Code 20 29
User Code 21 30
User Code 22 31
User Code 23 32
User Code 24 33
User Code 25 34
User Code 26 35
User Code 27 36
User Code 28 37
User Code 29 38
User Code 30 39
Remote Code (EGR100) 40
KeyFob 1 85
KeyFob 2 86
KeyFob 3 87
KeyFob 4 88
KeyFob 5 89