ELABO F1-1 Series Скачать руководство пользователя страница 17

Страница: 17 / 115

Full-electronic HV-Tester F1-1x Typs
2. SAFETY REGULATIONS

when working with high voltage!

Follow DIN EN 50191 (DIN VDE 0104). The EN standard regulates the

operation of test systems and test benches.

Attention high voltage:

The contact elements used for the HV and IS

test (test probes etc.) must be designed for the maximum voltage supplied

by the device.

2.13

Discharging test objects with internal capacitance

ttention discharge currents - mortal danger!!

particularly in

the case of test objects with internal capacitance (capacitors).

Particularly during tests with

, test objects with internal capacitance

can

store large amounts of charge

. After disconnecting, this charge

may be dissipated via the operator‘s body (if the test object is touched in

the appropriate place).
If the test object is left connected to the tester after switching off the high

voltage, it will discharge automatically via the tester. If this discharging

is prevented (disconnection), potentially fatal discharge currents may be

produced.

Note Ma

ins Switch:

Do not switch-off the Tester on running HV-/IS-test.

In this case, a correct discharge of the test object not ensure.

2.14 Discharging via the device

After the end of the test (end of test time), the test object connected is au-

tomatically discharged. For this purpose a discharge resistor is connected

internally and the voltage across the resistor read (residual voltage meas-

urement) The discharging is undertaken using an internal 5 MOhm resistor

until a voltage of 3000 V is reached, the device then connects a 2 MOhm

resistor in parallel. If the voltage doesn‘t underrun a residual voltage of 60 V

within - 10 s at DC / 500 ms at AC - the device indicates the fault message

„Attention residual voltage“.

Note:

The residual voltage measurement can be switched off on the „Setup“

menu or using an interface command (see the remote control manual).
Automatic discharging is performed only at DC test voltages. At AC, the

discharging of the test object is running via high-voltage transformer.

Att

ention:

Leave the test object connected until it is discharged. The

device indicates this state with the illumination of the green RUN button.

Additional discharging via an external resistor

The device has an output for the connection of an external discharge re-

sistor. At the end of the HV/ IS test this output is connected by the device.

On this topic see chapter 6.2.4.1 „Outputs/external discharge relay“.

Содержание F1-1 Series




















































































































Результаты поиска

Содержание F1-1 Series

Отзывы:

Похожие инструкции для F1-1 Series

Бренды по названию

Популярные бренды

ELABO F1-1 Series, Руководство по эксплуатации

Результаты поиска

Содержание F1-1 Series

Отзывы:

Похожие инструкции для F1-1 Series

Бренды по названию

Популярные бренды