Ekinex EK-CG2-TP Скачать руководство пользователя страница 91

Страница: 91 / 91

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

MAEKCG2TP_EN

Pag. 91

13 Warning

• Installation, electrical connection, configuration and commissioning of the device can only be carried out by qualified

personnel.

• Opening the housing of the device causes the immediate end of the warranty period.
• ekinex

KNX defective devices must be returned to the manufacturer at the following address:

SBS S.p.A. Via Circonvallazione s / n, I-28010 Miasino (NO) Italy.

13.1 Other information

• This application manual is aimed at installers, system integrators and planners
• For further information on the product, please contact the ekinex® technical support at the e-mail address:

[email protected] or visit the website www.ekinex.com

• ekinex® is a registered trademark of SBS S.p.A.
• KNX® and ETS® are registered trademarks of KNX Association cvba, Brussels

Содержание EK-CG2-TP




























































































Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Ekinex EK-CG2-TP, Руководство по применению, Страница: 91 / 91

Результаты поиска

Содержание EK-CG2-TP

Отзывы: