Ekinex EK-CG2-TP Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 91

Ekinex EK-CG2-TP Скачать руководство пользователя страница 58

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

© SBS S.p.A.

– Tutti i diritti riservati

MAEKCG2TP_EN

Pag. 58

9.6

Cooling

The

Cooling

folder includes the following parameters:

•

Comfort temp. setpoint [°C]

•

Standby temperature setpoint [°C]

•

Economy temp. setpoint [°C]

•

Building protection temp. setpoint [°C]

•

Cooling type

•

Control type

•

Hysteresis

•

Cyclic sending interval

•

Min. change of value to send [%]

•

PWM cycle time

•

Proportional band [0,1 K]

•

Integral time [min]

•

Anticondensation with probe

•

Anticondensation protection type 2

•

Auxiliary cooling

•

Disabled from bus

•

Offset from setpoint

•

Hysteresis ON/OFF [K]

9.6..1 Parameter and communication object tables

Conditions:

General

Thermostat function = cooling or both heating and cooling.

Parameter name

Conditions

Values

Comfort temp. setpoint [°C]

23

[range 10 … 50]

Standby temp. setpoint [°C]

26

[range 10 … 50]

For a correct operation of the device the standby temperature setpoint has to be >
comfort temperature setpoint.

Economy temp. setpoint [°C]

28

[range 10 … 50]

For a correct operation of the device the standby temperature setpoint has to be >
economy temperature setpoint.

Building protection temp. setpoint [°C]

36

[range 30 … 50]

Cooling type

fan-coils

floor radiant panels ceiling

radiant panels

If in Settings the parameter Thermostat function = both heating and cooling and
Command communication object = unique, the parameter Cooling type is bound to the
choice done for Heating.

Control type

Command communication object =
separated

2 point hysteresis

PWM (pulse width modulation)

continuous

If in Settings the parameter Thermostat function = both heating and cooling and
Command communication object = unique, the parameter Control type is bound to the
choice done for Heating.

«
...
56
57
58
59
60
...
»

Содержание EK-CG2-TP




























































































Отзывы:

Нет отзывов