Ekinex EK-CG2-TP Скачать руководство пользователя страница 31

Страница: 31 / 91

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

MAEKCG2TP_EN

Pag. 31

9.0.6 Independent or single: shutter or venetian blind

Object name

Conditions

Size

Flags

DPT

No. Comm. Obj.

Input x

–

Dedicated stop command

Input x = independent or

single

Function x = enabled

Type = shutter or venetian

blind

1 bit

CRWTU

[1.017]

trigger

13,30 (1A, 1B)

51,68 (2A, 2B)

Immediately stop any movement of the blind. The object is sent on a short press if the blind
mode is disabled and at the end of a long press if the venetian blind mode is enabled.

Input x

–

Stop

– step up/down command

Input x = independent or

single

Function x = enabled

Type = shutter or venetian

blind

Blind mode = enabled

1 bit

CR-T-

[1.007]

step

16,33 (1A, 1B)

54,71 (2A, 2B )

Move the blind to fully open or fully closed position. The object is sent at the end of a long
press.

Input x

–

Move up / down command

Input x = independent or

single

Function x = enabled

Type = shutter or venetian

blind

1 bit

CRWTU

[1.008]

up/down

17,34 (1A, 1B)

55,72 (2A, 2B)

Increase or decrease the opening of the blind stepwise.

The object is sent on a short press.

9.0.7 Independent or single: scene

Object name

Conditions

Size

Flags

DPT

No. Comm. Obj.

Input x

–

Scene number

Input x = independent or

single

Function x = enabled

Type = scene

1 Byte

CR-T-

[17.*]

Scene number

[18.*]

Scene control

18,35 (1A, 1B)

61,73 (2A, 2B)

Store or recall a scene. The lowest 6 bits in the byte form the code of the scene, while the
highest bit is the operation code (store or recall).

Содержание EK-CG2-TP




























































































Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Ekinex EK-CG2-TP, Руководство по применению, Страница: 31 / 91

Результаты поиска

Содержание EK-CG2-TP

Отзывы: