Ekinex EK-CG2-TP Скачать руководство пользователя

Страница: 72 / 91

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

MAEKCG2TP_EN

Pag. 72

Signal from bus

Disable dehumid. control from bus = yes

not inverted

/ inverted

Object name

Conditions

Dim.

Flags

DPT

Comm. Obj. No.

Relative humidity setpoint for
dehumidification

2 Byte

CRWTU-

[9.007] humidity (%)

Dehumidification command

1 Bit

CR-T--

[1.001] switch

Dehumidification water battery
command

Temperature control

Settings

Thermostat

function = both
heating and

cooling,

Temperature

control cooling
cooling type = floor
radiant panels or
ceiling radiant
panels,

Relative humidity

dehumidification

function = cooling

1 Bit

CR-T--

[1.001] switch

Dehumidification integration
control

Temperature control

Settings

Thermostat

1 Bit

CR-T--

[1.001] switch

Object name

Conditions

Dim.

Flags

DPT

Comm. Obj. No.

function = both
heating and

cooling,

Temperature control

cooling

cooling type = floor

radiant panels or
ceiling radiant

panels,

Relative humidity

dehumidification

function = cooling

This object switches ON if (simultaneously) the relative humidity is greater than the relative
humidity setpoint and the room temperature is greater than the setpoint of the parameter

Temperature difference for integration.

Dehumidification control disable

1 Bit

C-W---

[1.002] boolean

Содержание EK-CG2-TP




























































































Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Похожие инструкции для EK-CG2-TP

Бренды по названию

Популярные бренды

Ekinex EK-CG2-TP, Руководство по применению

Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Похожие инструкции для EK-CG2-TP

Бренды по названию

Популярные бренды