Ekinex EK-CG2-TP Скачать руководство пользователя страница 71

Страница: 71 / 91

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

MAEKCG2TP_EN

Pag. 71

9.9.1 Dehumidification

The secondary folder

Humidification

includes the following parameters:

•

Operating modes where dehumidification is active

•

Relative humidity setpoint for dehumidification control [%]

•

Dehumidification control hysteresis [%]

•

Dehumidification secondary to temperature control

•

Function of integration of sensible heat

•

Disable from bus

9.9.1.1

Parameter and communication object tables

Parameter name

Conditions

Values

Dehumidification function

disabled

cooling

heating

both cooling and heating

Parameter that selects the dehumidification function.

Humidity setpoint [%]

Dehumidification function ≠ disabled

[range 30 … 60]

Hysteresis

Dehumidification function ≠ disabled

0,8 %

[other values in the range 0,5 … 4%]

Subordinated to temperature control

Temperature control Settings

Thermostat function = both heating and
cooling,

Temperature control cooling cooling

type = floor radiant panels or ceiling
radiant panels,

Relative humidity dehumidification

dehumidification function = cooling

no /

yes

Dehumidification start delay

Subordinated to temperature control =

00:05:00 hh:mm:ss

[range

00:00:00 … 18:12:15]

Value 00:00:00 means that the start delay is disabled.

Integration

/ yes

Temperature difference for integration

Integration = yes

1,5°C

[other values in the range 0,5 … 3°C]

Hysteresis for integration

Integration = yes

0,5 K

[other values in the range 0,2 K … 3 K]

Cyclic sending interval

no sending

[other values in the range 30 s … 120

min]

Value 00:00:00 means that the cyclic sending is disabled.

Disable dehumid. control from bus

/ yes

Содержание EK-CG2-TP




























































































Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Ekinex EK-CG2-TP, Руководство по применению, Страница: 71 / 91

Результаты поиска

Содержание EK-CG2-TP

Отзывы: