background image

EPX400-A20CU – Manual 

Page 39 / 62 

 

 

Each  rule  comprises  a  pair:  a  fragment  of  the  sender's  phone  number  and  a  valid 
phone  number  of  the  recipient.  A  fragment  of  the  sender's  phone  number  can,  in 

extreme cases, consist of an empty string, which means ability to match any phone 
number. Processing of the rules is carried out according to the set sequence from the 

beginning to the end, i.e. the result of processing one rule does not affect processing 

of  the  subsequent  rules.  This  also  means  that  the  text  message  can  be  sent  to 
several phone numbers, or that the same message can be sent several times to the 

same  number.  Such  a  case  occurs  if  the  condition  imposed  on  the  sender's  phone 
number is met for at least two rules with the same number of the recipient. 

NOTE:

 The user takes responsibility for the proper administration of numbers so that 

no loop could create in text messaging. 

 

Text message notifications 

8.4.4.

In  this  section  you  can  define  up  to  10  numbers  to  users  which  will  be  informed 
about  the  selected  events  using  text  messages.  To  do  that,  press 

  and  in  the 

window displayed, define telephone number and select the type of events being sent. 

 

Custom SMS messages 

8.4.4.1.

In  this  section  you  can  add  a  new  (by  pressing 

  )  and  edit  already  defined  (by 

pressing 

)  the  text  of  unique  SMS  messages  that  can  be  assigned  to  the  events 

below in the "Status" section. 

 

SMS notification 

8.4.4.2.

In this section you can define up to 5 numbers for users who will be informed about 
selected events using the defined SMS messages that have been assigned to them. 
To do this, press   and define the phone number in the window that appears, select 

the type of events to be sent and confirm then by clicking 

Add

Содержание EPX PRO































































Отзывы: