Eaton Magnefix MD4 Скачать руководство пользователя страница 79

Страница: 79 / 109

Magnefix MD4

991.184 G01 03

4.2.2

Switching off

Switching off the cable panel and branch-circuit

panel

ARNING

Refer to the safety instructions in paragraph 4.1.2.

Procedure for switch caps

1. Place the springing handle on the switch cap.

2. Pull the handle firmly.



The switch cap disengages from the fixed part.

1, 2

Place a clean, dry cover on the open cast resin

insulated member of the switch.

If (maintenance) work is scheduled to be performed,

the installation must have protective earthing.

Switching off a protected panel

3 Cover for cast resin insulated member of switch

Procedure for protected panel

If the relay has switched off the protected panel:



the electronic trip indicator (9) will show a red field;



the mechanical position indicator (5) will show a

white field.

Verify this.

If the position indicator (5) shows a black field, press

the button (6) The vacuum circuit-breaker will then

switch off.

Remove the corresponding switch caps (12) one by

one in line with the above procedure.

If (maintenance) work is scheduled to be performed,

the installation must have protective earthing.

If you are about to carry out measurements, switch on

the vacuum circuit-breaker in line with the above
procedure “Switching on for maintenance work” and

then lock it to prevent switching off, using the relevant

key-operated earthing interlock locking knob.

Содержание Magnefix MD4














































































































Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды

Eaton Magnefix MD4, Руководство пользователя

Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды