Eaton ARCON 3G, Инструкция по эксплуатации

Страница: 74 / 104

74
ARCON 3G
ARCON 3G MANUAL
MN026015EN October 2020 www.eaton.com
The Master MAIN firmware checks its peripherals, flags from all modules on the
INTERLINK, iCOM, Ignition port and MASTERLINK. If an error or trip is encountered, then
the according event will be set. Furthermore, the on-board watchdog is used for the self-
monitoring of the entire system. Alarms are events which require user acknowledgment
(ACK is “YES” in table below). An Alarm disappears only if it is acknowledged and the
trigger condition is false. The alarms are saved non-volatile, so in case of loss of supply
voltage the active alarms are not lost. After return of supply voltage all previous active
alarms will be restored. If TRIP alarm is restored, then the output relays will be activated
again, but NOT the ignition command to the quenching device.
For details about the impact of events on master LEDs and relays please find the
table below:
Prefix Number Text Description ACK
Relay
TRIP 1
Relay
TRIP 2
Relay
TRIP 3
Relay
Trip alarm
Relay
Watchdog LED System LED TRIP LED RUN
9
LED TRIP
10
IGNITION PIN
1 RESTART System starting. NO OPEN OPEN OPEN OPEN OPEN OFF OFF OFF OFF RESET
3 START ADDRESSING Addressing process started. NO - - - - - - - - - -
E 4 ADDRESSING ERROR Error detected in addressing process. YES - - - - OPEN Red / 2Hz - - - -
5 ADDRESSING OK Addressing process finished successfully. NO - - - - - - - - - -
E 6 FLASH ACCESS ERROR Serial flash memory error detected. YES - - - - OPEN Red / 2Hz - - - -
8 START INITIALIZATION Initialization process started. NO - - - - - Orange / 2Hz - - - -
E 9 PARAMETERIZATION ERROR Error while parameterization process. YES - - - - OPEN Red / 2Hz - - - -
10 PARAMETERIZATION OK The parameterization process is completed successfully. NO - - - - - - - - - -
11 INITIALIZATION FINISHED Initialization process finished. NO - - - - - - - - - -
12 START NORMAL OPERATION MODE Entering into normal operation mode. NO - - - - CLOSED Green / 1Hz - Green / 1Hz - -
T 13 TRIP Arc protection trip detected. YES CLOSED CLOSED CLOSED CLOSED - Red / 2Hz Red OFF Red SET
E 14 WD RESET On chip watchdog reset happened. YES - - - - OPEN Red / 2Hz - - - -
E 15 ADC ERROR ADC error detected. YES - - - - OPEN Red / 2Hz - - - -
E 16 DAC ERROR DAC error detected. YES - - - - OPEN Red / 2Hz - - - -
E 17 PARAMETER ERROR Parameter error detected.(parameter missing or over range) YES - - - - OPEN Red / 2Hz - - - -
E 18 SENSOR WIRE FAULT Sensor wire fault detected. YES - - - - OPEN Red / 2Hz - - - -
E 19 SENSOR CONSTELLATION ERROR Unexpected sensor detected. YES - - - - OPEN Red / 2Hz - - - -
E 20 INTERLINK ERROR INTERLINK communication error. (CAN bus error) YES - - - - OPEN Red / 2Hz - - - -
E 21 INTERLINK CONSTELLATION ERROR INTERLINK module missing or unexpected module detected. YES - - - - OPEN Red / 2Hz - - - -
E 22 INTERLINK COMPATIBILITY ERROR INTERLINK compatibility error. YES - - - - OPEN Red / 2Hz - - - -
E 24 UPF ERROR User parameter file (UPF) missing or corrupted. YES - - - - OPEN Red / 2Hz - - - -
E 25 MPF ERROR Manufacture parameter file (MPF) missing or corrupted. YES - - - - OPEN Red / 2Hz - - - -
26 PARAMETER CHANGED Parameter change detected. NO - - - - - - - - - -
27 USER MODE Entering into user mode. NO - - - - - - - - - -
28 PROTECTED MODE Entering into password protected mode. NO - - - - - - - - - -
29 MANUFACTURER MODE Entering into manufacturer mode. NO - - - - - - - - - -
E 30 ICOM ERROR iCOM communication error. (CAN bus error). YES - - - - OPEN Red / 2Hz - - - -
Events & Alarms