DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 52

background image

- 7 -

Radial Plate to Mounting Pipe

Place the optional

DXE-RADP-3

Radial Plate over the optional

DXE-

VGMT-3GC

3” mounting pipe.

Connections to the antenna will be
made via the optional

DXE-UHF-

FDFB-KIT

SecureMount

™

bulkhead

fitting dual SO-239 connector. The

DXE-RADP-3

Radial Plate comes

with 20 sets of stainless steel
hardware for mounting the radial
wires. It is suggested that 32 radials
each 65 feet long be used. Longer
radial wires, up to 135 feet each,
would provide an improvement in
signal strength for this 160 meter
antenna. Additional

DXE-RADP-1HWK

Radial Plate Wire Attachment Hardware

Optional DXE-RADP-3 Radial Plate Mounted to

Kits will be required.

a 3" OD Mounting Pipe

Attaching Ground Radial Wires to the Radial Plate

Using the 20 sets of supplied 1/4" stainless steel hardware (Bolt, Star Washer, Flat Washer, Split
Washer, Nut) connect the optional ground radial wires to the

DXE-RADP-3

Radial Plate as shown

below. Additional hardware kits are available (

DXE-RADP-1HWK

) that contain 20 sets of Radial

Plate Hardware.

There are optional DX Engineering Radial Wire Kits available.

DXE-RADW-500K/BD

contains a

500 foot spool of 14 gauge copper stranded wire with black PVC insulation, 20 Terminal Lugs and
100 Steel or Biodegradable Lawn Staples. The

DXE-RADW-1000K/BD

Radial Wire Kit contains

a 1,000 foot spool of 14 gauge copper stranded wire with black PVC insulation, 40 Terminal Lugs
and 200 Steel or Biodegradable Lawn Staples.

RADW-65RT

contains 20 each 65 foot radial wires

with 1/4" terminal attached.

Depending on the number of radial wires used, space them out evenly around the Radial Plate. The
Radial Plate will accommodate up to 60 radial wires (60 laser drilled holes), or up to 120 radials if
doubled up.

«
...
6
7
8
9
10
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: Wavetrend Страницы: 2

Бренд: Sirio Antenne Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 16

Бренд: Philips Страницы: 17

DHI-ISC-EAA6000-P

Бренд: Dahua Страницы: 28

Бренд: Williams Sound Страницы: 2

Бренд: Williams Sound Страницы: 4

Бренд: Intellian Страницы: 141

Бренд: Ellies Страницы: 2

Бренд: CommScope Страницы: 8

Бренд: Wade Страницы: 2

airMAX airGrid M2 HP

Бренд: Ubiquiti Страницы: 20

Бренд: Cabletech Страницы: 24

Premium OYSTER 65

Бренд: Ten-Haaft Страницы: 27

Бренд: Benelec Страницы: 6

Бренд: TracVision Страницы: 2

Бренд: TracVision Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды