DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

background image

- 10 -

5. Locate two V-Saddle blocks, two stainless steel V-Bolts, four stainless steel 3/8" flat washers,

four stainless steel 3/8" split lock washers and four stainless steel 3/8-16 hex head nuts. Loosely
assemble (one or two threads beyond the end of the hex nuts) the two V-Bolts to the stainless
steel base side bottom hinge as shown below. The V-Bolts will be tightened in a later assembly
step.

6. Locate the stainless steel Pivot Base Winch Mount, two stainless steel Pivot Base Plate

Brackets, four 3/8-16 x 1-1/4" long stainless steel hex bolts, eight stainless steel 3/8" flat
washers, four stainless steel 3/8" split lock washers and four stainless steel 3/8-16 hex nuts.
Assemble the Pivot Base Plate Brackets to the Pivot Base Winch Mount as shown below.

7. Locate four 3/8-16 x 1-1/4" long stainless steel hex bolts, eight stainless steel 3/8" flat washers,

four stainless steel 3/8" split lock washers and four stainless steel 3/8-16 hex nuts. Mount the
Pivot Base Winch Mount assembly to the stainless steel Pivot Base Locking Plate.

«
...
9
10
11
12
13
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: AKO Страницы: 2

Бренд: KVH Industries Страницы: 51

Бренд: Winegard Страницы: 1

AVANT CPE 150Mbps

Бренд: Smart Lan Страницы: 11

Бренд: MFJ Страницы: 2

Бренд: Jegs Страницы: 4

Бренд: Huawei Страницы: 25

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 13

Straight Talk H258C

Бренд: Huawei Страницы: 22

Бренд: Kenwood Страницы: 7

Бренд: Kenwood Страницы: 4

Бренд: Somogyi Страницы: 11

Бренд: SteppIR Страницы: 46

Бренд: SteppIR Страницы: 52

Dinova Boss DINOVATF1

Бренд: Televes Страницы: 24

Бренд: Naxa Страницы: 2

Бренд: Moen Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды