DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 52

background image

- 26 -

Mating the Vertical Element to the Pivot Base Assembly

1. To lower the antenna, ensure the winch hook is in the Antenna Hook Mount. Remove the four

bolts and hardware that hold the Pivot Lock Plate to the Pivot Base Winch Mount Plate. You
can now use the winch to pivot the antenna downward.

Four Bolts to be removed to allow for pivoting

2. Locate the 3-1/2" long 1/4" bolts,

four stainless steel flat washers
and two 1/4" stainless steel
Nyloc nuts. Align the 3" OD base
section element with the
assembled vertical elements.
Slide the 2.75" element section
into the 3" OD base element
section aligning the 4 holes.

«
...
25
26
27
28
29
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: Ubiquiti Страницы: 24

SPA 2400/75/9/0/V - FICHE TECHNIQUE

Бренд: HUBER+SUHNER Страницы: 2

OMNIANGLE OA-144

Бренд: PAR Страницы: 4

LPDA7030-11-10SMA

Бренд: RFI Страницы: 4

Бренд: Hama Страницы: 8

Бренд: Etec Страницы: 8

StreetPilot 2730

Бренд: Garmin Страницы: 68

Бренд: Streakwave Страницы: 15

DMX, DMXMD, DMXHD

Бренд: WADE Antenna, Inc. Страницы: 2

Бренд: Steren Страницы: 2

Бренд: Steren Страницы: 6

Бренд: A.H. Systems Страницы: 13

Бренд: H3C Страницы: 8

Бренд: M2 Antenna Systems Страницы: 6

Бренд: Taoglas Страницы: 8

Бренд: Taoglas Страницы: 19

Little Tarheel II

Бренд: Tarheel Antennas Страницы: 6

Бренд: Tarheel Antennas Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды