DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 52

background image

- 50 -

TES-2155

-

3M Temflex™ 2155 Rubber Splicing Tape

Conformable self-fusing rubber electrical insulating tape. It is designed for low voltage electrical insulating and moisture
sealing applications. For outdoor use, it should be protected from UV deterioration with an overwrap of

TES-06132.

TES-06132 - Scotch

®

Super 33+

Highly conformable super stretchy tape for all weather applications. This tape provides flexibility and easy handling for all
around performance. It also combines PVC backing with excellent electrical insulating properties to provide primary
electrical insulation for splices up to 600V and protective jacketing. Both tape products are available from DX Engineering.

RigExpert

®

Antenna Analyzers

RigExpert

®

Antenna Analyzers are powerful antenna analyzers designed for testing, checking, tuning, or repairing antennas and

antenna feed-lines. Mainly, these are SWR (Standing Wave Ratio) and impedance measurement instruments (vector impedance
analyzers). Their large, bright LCD screens provide graphic illustration of SWR, impedance, return loss and much more. Easy-to use
measurement modes, as well as additional features such as connection to a personal computer (to plot Smith charts, etc.), make
RigExpert

®

analyzers attractive for professionals and hobbyists alike. The graphic display of various parameters over a wide

frequency range is a key feature of these analyzers. This significantly reduces the time required to adjust an antenna. RigExpert

®

Antenna Analyzers are available in several models and in various frequency ranges of operation. Each is fitted with an SO-239
female connector, except for those models that will operate above 230 MHz, where a Type N connector is more efficient.

The following tasks are easily accomplished by using RigExpert

®

Antenna Analyzers:

* Rapid check-out of an antenna
* Tuning an antenna to resonance
* Antenna SWR and impedance measurement
* Making coaxial lines or measuring their parameters
* Cable testing and fault location
* Measuring capacitance or inductance of reactive loads

DXE Part Number

Frequency Range

REU-AA-35ZOOM

0.6 to 35 MHz

REU-AA-55ZOOM

0.6 to 55 MHz

REU-AA-230ZOOM

0.1 to 230 MHz

REU-AA-600

0.1 to 600 MHz

«
...
49
50
51
52
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: Kathrein Страницы: 48

Бренд: Kathrein Страницы: 26

Бренд: H3C Страницы: 6

Бренд: Chameleon Antenna Страницы: 24

Бренд: Crest Audio Страницы: 4

Бренд: NXP Semiconductors Страницы: 45

MS-MBA-3.2-H4-L4

Бренд: Matsing Страницы: 5

Бренд: One for All Страницы: 2

Бренд: Oricom Страницы: 2

Бренд: Faria Страницы: 4

Бренд: MotoSAT Страницы: 2

SlimLine Multi-Satellite Dish Antenna

Бренд: DirecTV Страницы: 15

Yagi DSE3319LYCEL

Бренд: Directive Systems & Engineering Страницы: 3

Бренд: DirecTV Страницы: 48

Бренд: Dynalink Страницы: 4

Mantis Motorised MSAT ACU

Бренд: Vislink Страницы: 60

Бренд: Novus Страницы: 5

Бренд: Jaybeam Wireless Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды