DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 52

background image

- 28 -

Base Series and Shunt Coil Assembly and Installation

Two coils are used at the base of the antenna. One coil is in series with the antenna feed point; the
other coil is shunt coil and is connected to the Radial Plate. Attach the series coil with the straight
bracket on the antenna feedpoint using the hardware as shown.

Install the shunt coil with the “L” bracket to the radial plate on top of an existing radial wire bolt
using the hardware as shown below. The wire (with terminals) is connected from one end of the
series coil to the shunt coil (top connection). At this same connection point the wire with the PL-
259 on the other end, is connected to this same point.

Position the shunt coil on the Radial Plate to allow the wire to connect to the series coil and not
interfere when pivoting the antenna.

«
...
27
28
29
30
31
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: Adeunis RF Страницы: 7

Бренд: M2 Antenna Systems Страницы: 5

Бренд: KING Страницы: 36

Бренд: Ventev Страницы: 2

Бренд: ICC Страницы: 17

RetroAntenna PA01

Бренд: RetroSound Страницы: 4

Бренд: CommScope Страницы: 8

Бренд: OBID Страницы: 71

Rayzar.Air RVRZ25B

Бренд: Winegard Страницы: 12

Pulse LARSEN LM Series

Бренд: Yageo Страницы: 2

Pulse YA Series

Бренд: Yageo Страницы: 2

Бренд: Radio Shack Страницы: 4

Бренд: Radio Shack Страницы: 4

Antenna Rotator

Бренд: Radio Shack Страницы: 4

Бренд: trig Страницы: 2

Бренд: M2 Antenna Systems Страницы: 5

8000 ACS Series

Бренд: Radeus Страницы: 24

2x2 Omni Antenna

Бренд: Xirrus Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды