DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 52

background image

- 15 -

14. Tighten the two U-Bolt clamps hardware evenly so the length of the exposed threads is

approximately equal. Any clamp should be tightened evenly from side-to-side with an equal
amount of thread above each nut.

15. Locate the 1/4-20 x 1.25" long stainless steel hex bolt, two 1/4" stainless steel external tooth

lock washers, one 1/4" stainless steel flat washer and one stainless steel 1/4-20 hex nut. Install
the feedpoint hardware at the bottom of the 3" OD bottom element in the pre-drilled hole as
shown below.

View showing the feedpoint hardware installed

Mounting and using the Optional DXE-VRW-1 Manual Winch

1. Follow the instructions included with the optional

DXE-VRW-1 -

Manual Winch Add-On Kit

to prepare the Manual Winch for installation on the antenna base assembly.

2. Included with optional

DXE-VRW-1 -

Manual Winch Add-On Kit is the

stainless steel hardware for mounting the winch on the pivot base assembly.
The hardware includes three 3/8-16 x 1" long stainless steel hex bolts, six
stainless steel 3/8-16 flat washers and three 3/8-16 Stainless Steel Nyloc Nuts.

3. Loosely install the three sets of stainless steel hardware on the manual winch as shown below.

«
...
14
15
16
17
18
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

Бренд: M2 Antenna Systems Страницы: 12

Бренд: Channel Master Страницы: 2

Бренд: 305 BROADCAST Страницы: 9

Бренд: Majestic Страницы: 2

Бренд: Aerohive Страницы: 4

Бренд: Labgear Страницы: 1

Бренд: HyperLink Technologies Страницы: 3

Бренд: King-Dome Страницы: 40

Бренд: Bricon Страницы: 4

Бренд: ViaSat Страницы: 65

Бренд: Ikan Страницы: 24

Бренд: RCA Страницы: 12

Бренд: Vision Plus Страницы: 2

Oyster CYTRAC DX Premium

Бренд: Ten-Haaft Страницы: 11

Бренд: Solid Signal Страницы: 12

Бренд: Simrad Страницы: 16

Бренд: 1byone Страницы: 2

Бренд: 1byone Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды