DX Engineering DXE-160VA-1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 52

background image

- 11 -

Note: These four bolts are removed when using the pivoting function as described later on in
this manual.

8. Locate two V-Saddle blocks, two stainless steel V-Bolts, four stainless steel 3/8" flat washers,

four stainless steel 3/8" split lock washers and four stainless steel 3/8-16 hex head nuts. Loosely
assemble (one or two threads beyond the end of the hex nuts) the two V-Bolts to the stainless
steel Pivot Base Winch Mount as shown below. The V-Bolts will be tightened in a later
assembly step.

9. Locate two thick stainless steel Backing Plates, two thin stainless steel Backing Plates, two

U-Bolt Saddle blocks, two stainless steel U-Bolts, four stainless steel 3/8" flat washers, four
stainless steel 3/8" split lock washers and four stainless steel 3/8-16 hex head nuts.

«
...
10
11
12
13
14
...
»

Содержание DXE-160VA-1





















































Отзывы:

Нет отзывов

Похожие инструкции для DXE-160VA-1

TRIUMPH-1M Plus

Бренд: Javad Страницы: 26

Бренд: Matchmaster Страницы: 2

Precision MXL012/55NZ

Бренд: Maxview Страницы: 12

Бренд: Maxrad Страницы: 2

ANT-4G-OMNI-OUT-N

Бренд: Cisco Страницы: 11

ANT-4G-CM-IN-TNC

Бренд: Cisco Страницы: 9

ANT-WPAN-OD-OUT-N

Бренд: Cisco Страницы: 8

ANT-4G-PNL-OUT-N

Бренд: Cisco Страницы: 22

Catalyst C-ANT9103 Series

Бренд: Cisco Страницы: 28

ProCurve J9169A

Бренд: HP Страницы: 4

ProCurve J8444A

Бренд: HP Страницы: 2

ProCurve J8445A

Бренд: HP Страницы: 2

5009-33 BROADBAND-AT-SEA

Бренд: Sea Tel Страницы: 145

Бренд: Winegard Страницы: 1

Movin' View MV3500T

Бренд: Winegard Страницы: 8

RetroAntenna PA01

Бренд: RetroSound Страницы: 4

Бренд: Schlage Страницы: 16

CMAX-OMFX-43M-I53

Бренд: CommScope Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды