DTM Print LX610e Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 114

background image

102 |

Note on PC Settings:

Most applications allow you to change these same printer driver options from their “Print” and/or “Printer
Setup” screens. Some applications such as BarTender save your settings with the label, others use settings
only for the current print job just sent to the printer.

Paper Size

If you are using BarTender, this setting is adjusted during the label setup wizard. If you are using a program
other than BarTender you will need to set this to the dimensions of your label. Keep in mind that the
dimensions are always relative to the width and height of the actual label in the printer. Orientation of an
image on the label should not change this setting. See Section 2A for minimum and maximum label sizes.

Orientation

There are two settings for orientation, Portrait and Landscape. If your text and graphics print left to right
or as shown on the screen, select portrait. If you wish your printing to rotate 90 degrees from what you see
on the screen so it is printing horizontally, select landscape as your orientation. Remember, this does not
change the width and height Paper Size. It is only a tool for viewing a label upright on screen that will be
printed sideways on the printer.

Print Quality

There are 4 levels of print quality in the driver. The lower the quality, the faster the print. Quality 1 provides
the fastest print available while Quality 4 provides the best quality. It is recommended that you experiment
with the different levels when designing your label to find a good balance between print quality and print
speed. Quality 2 is the default.

Color Matching

There are several options available depending on which cartridge is installed (Pigment or Dye). The options
will update automatically depending on which cartridge is installed.

Vivid Graphics

mode is best used for graphical images where accurate color reproduction is not as

essential. Images printed in this mode will look more vibrant because more ink is being used to produce
them.However, printing images of people may produce skin tones that have a reddish tint.

Vivid Photos

mode is best used for photographic images where accurate color reproduction is very

essential. Images printed in this mode will look lighter than those printed in Vivid Graphics mode. Skin
tones especially will look more natural in this mode.

ICC Gloss Paper, ICC Gloss Polyester and ICC Matte Bopp

are all ICC calibrated color matching options.

Select the setting that corresponds to your installed Primera media of the same type to produce ICC color
matched prints. Note: ICC monitor calibration and additional setup is required for this option to work.

-NONE-

will use no color matching.

«
...
100
101
102
103
104
...
»

Содержание LX610e



















































































































Отзывы:

Нет отзывов

Похожие инструкции для LX610e

KITCHEN PRO K6725

Бренд: Regal Ware Страницы: 62

Бренд: U-Line Страницы: 2

Ice Undercounter Series Cubers ICEU070A

Бренд: Ice-O-Matic Страницы: 21

Бренд: Kalorik Страницы: 28

Бренд: Simonelli Страницы: 192

Бренд: Kleenmaid Страницы: 36

Saeco Xelsis HD8944/01

Бренд: Philips Saeco Страницы: 3

Бренд: Browne & Co Страницы: 9

Бренд: Gaggia Страницы: 92

Бренд: Lagrange Страницы: 62

iCoffee Davinci

Бренд: Remington Страницы: 16

Бренд: Gaggia Страницы: 4

Caffeo Varianza CSP

Бренд: Melitta Страницы: 250

Бренд: Casio Страницы: 65

Бренд: Rancilio Страницы: 60

Бренд: WOOSIM Страницы: 35

Бренд: LAVAZZA Страницы: 172

Бренд: Toastmaster Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды