Doosan B20S-3 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 123

Doosan B20S-3 Скачать руководство пользователя страница 101

100

MicroController Control System

Testing And Adjusting

Component Tests

Battery  voltage  and  high  amperage  are  present.
Injury  to  personnel  is  possible.  Disconnect  the
battery  and  discharge  the  head  capacitor  (HEAD
CAP) before any contact is made with the control
panel.

NOTICE

Do not use steam or solvent to clean the controls.
Damage  can  be  caused  to  the  control  panel.  Use
pressure  from  an  air  hose  with  a  maximum
pressure  of  205  kPa  (30  psi)  to  clean  the  control
panel  when  necessary.  The  air  supply  must  be
equipped with a water ﬁlter.

NOTE:

When control wires and power cables or bus

bars are to be connected to the same bolt or
stud, place all control wires together on the
top of the bus bar or power cable.

Use the electrical schematic (located inside rear
panel cover) to locate components referred to by
name and number in the procedures that follow.
All wires must be located as shown on the schematic.
Refer to SB4087E00 schematic(A174502) as
attached.

WARNING

Conductor and Switch Continuity

1.

Set the multimeter to the 200

Ω

range.

2.

Use the multimeter to perform the continuity test. lf

continuity exists, the measurement will be less
than 1 ohm. lf the measurement is more than this,
continuity does not exist and the problem will have
to be repaired.

«
...
99
100
101
102
103
...
»

Содержание B20S-3




























































































































Отзывы:

Нет отзывов