Datasat LS10 Скачать руководство пользователя страница 100

Страница: 100 / 118

LS10 Installation and Operating Guide

Version 1.01

Appendix E. LS10 Remote Command API

E-

Document #: 9301H66300 Ver. 1.01

Input Selection Commands

1. Input Selection

Command:

INPUT

<space>

[input]

<CR>

Operation

Response:

INPUT

<space>

input

<CR>

Read/Write

This is used to select a new input, or view the current input.

Parameters

input

Identifies the desired or selected input name. For the set command to be

successful, the name must be one of the input names:

Stereo 1

Stereo 2

USB

TosLink 1

TosLink 2

SPDIF 1

SPDIF 2

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

HDMI 6

HDMI 7

HDMI 8

Note

: Names with a space must use exactly one space.

Upper/lower cases in the name must be followed.

Example

Set the Input to Stereo 1

Send:

@INPUT

Stereo

1<cr>

Receive:

INPUT

Stereo

1<cr>

2. EQ Selection

Command:

EQSET

<space>

[eq]

<CR>

Operation

Response:

EQSET

<space>

<CR>

Read/Write

This is used to select a new EQ set, or view the current EQ set.

Parameters

EQ1 or EQ2

Example

Select EQ2

Send:

@EQSET EQ2<cr>

Receive:

EQSET EQ2<cr>

Содержание LS10























































































































Результаты поиска

Содержание LS10

Отзывы:

Похожие инструкции для LS10

Бренды по названию

Популярные бренды

Datasat LS10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LS10

Отзывы:

Похожие инструкции для LS10

Бренды по названию

Популярные бренды