Danfoss VLT5000 SyncPos страница 30 Скачать руководство пользователя

Страница: 30 / 236

MG.10.J8.02 – VLT is a registered Danfoss trade mark

Programmable SyncPos motion controller

■

Setting of SyncPos parameters: Velocity

This parameters you will find in the parameter

group V

Velocity

elocity

elocity in the menu "CONTROLLER"

→

"PARAMETER"

→

"AXIS":

VELMAX (1)

Maximum velocity

of the shaft where the encoder

is mounted in RPM.

N B!

For synchronizing the setting must be at

least the same as the maximum velocity of

the master in order to be able to synchronize. For

position synchronizing it must even be higher so

that the slave can catch up lost position related to

the master. All velocity commands (VEL, CVEL) are

related to this value.

RAMPMIN (31)

The

Shortest ramp

is the time from 0 to maximum

velocity and from maximum velocity to 0. All accele-

ration and deceleration commands (ACC. DEC) are

related to this value.

■

Setting of SyncPos option parameters: Home

Homing is not necessary in standard synchroniza-

tion applications and applications using an abso-

lute encoder.

When using an incremental encoder the controller

must be run to home after being switched on.

During this process the reference switch defines

the position at which 0 is located and how the VLT

functions during a home run: input depends on the

application.

HOME_VE L (7)

Home speed

is entered in % relative to the

maximum speed

of the drive.

You can find these values in the description of the

motor.

■

Setting of SyncPos parameters:
Synchronization

The following parameters are only relevant for

synchronizing applications: Open in the menu

"CONTROLLER"

→

"PARAMETERS"

→

"AXIS" the

parameter group Synchronization.

Synchronization.

SYNCFACTM (49) and SYNCFACTS (50)

The

Synchronizing factors master

and

slave

SYNCFACTM and SYNCFACTS must be set accor-

ding to the gear ratio between master and slave

encoder.

Example: Both encoders has 1024 ppr, master is

running 305 RPM and slave must run 1220 RPM.

SYNCFACTM =

305 and

SYNCFACTS =

1220.

Alternative:

SYNCFACTM = 1

SYNCFACTS = 4.

The following parameters are only relevant when

using synchronizing with marker correction

(SYNCM).

Open the parameter group Synchronization

Synchronization

Synchronization in the

menu "CONTROLLER"

→

"PARAMETERS"

→

"AXIS":

SYNCMARKM (52) and SYNCMARKS (53)

Number of master marker pulses and number of

slave marker pulses.

SYNCMARKM and SYNCMARKS must be set

according to the ratio between the number of

marker signals from master and slave. A ratio of

1:1 means that each slave marker will be aligned

with each master marker. A ratio of 2:1 means that

each slave marker will be aligned with each

second master marker.

Starting the SyncPos motion controller step-by-step

Содержание VLT5000 SyncPos













































































































































































































































Результаты поиска

Содержание VLT5000 SyncPos

Отзывы:

Похожие инструкции для VLT5000 SyncPos

Бренды по названию

Популярные бренды

Danfoss VLT5000 SyncPos, Руководство по эксплуатации

Результаты поиска

Содержание VLT5000 SyncPos

Отзывы:

Похожие инструкции для VLT5000 SyncPos

Бренды по названию

Популярные бренды