Danfoss VLT5000 SyncPos Скачать руководство пользователя страница 34

Страница: 34 / 236

MG.10.J8.02 – VLT is a registered Danfoss trade mark

Programmable SyncPos motion controller

2. A closed-loop PID control. The PID controller

monitors the difference between the actual

position and the setpoint position. Based on

this information it calculates a control signal to

minimize the position deviance. Thus the

SyncPos option is able to compensate for

changes in load or friction. The PID controller is

also necessary to compensate for any position

deviance caused by inaccurate setting of the

open-loop feed-forward controller.

In short: The feed-forward control is used to handle

changes in the setpoint reference (especially impor-

tant in synchronization applications), while the PID

control is used to handle changes in load conditions

or inaccuracies of the feed-forward control.

Proportional factor KPROP (11)

The

Proportional factor

is multiplied with the posi-

tion deviance and the result is added to the con-

trol signal (the internal speed-reference to the VLT).

Since the calculated control signal is proportional

to the position deviance (or error) this kind of con-

trol is called proportional control. The behavior of

the proportional control is similar to that of a spring

– the further the spring is extended the stronger

the counter-force it produces.

Influence of the Proportional factor

Proportional factor

Proportional factor:

KPROP too small large position deviation due to

non-compensatable load and

frictional moment;

KPROP larger

quicker reaction, smaller

steady-state deviation, larger

overshoot, lesser damping;

KPROP too great heavy vibrations, instability.

Derivative factor KDER (12)

The

Derivative factor

is multiplied with the deriva-

tive of the position deviance (the 'velocity' of the

position deviance) and the result is added to the

control signal. The behavior of the derivative con-

trol is similar to that of an absorber – the faster the

absorber is extended the stronger the counter-

force it produces. Thus using the

Derivative factor

increases damping in your system.

Influence of the Derivative factor

Derivative factor

Derivative factor:

KDE R small

no effect;

KDER larger

better dampening, lesser over-

shoot; if KPROP is increased

simultaneously: faster reaction

to control deviation at the same

level of vibration;

KDER too large

heavy vibrations, instability.

Integral factor KINT (13)

The sum of all error is calculated every time the

control signal is updated. The

Integral factor

then multiplied with the sum of all positioning

errors and added to the overall control signal. Thus

in case that steady-state position errors occurs in

your application, make sure you use the integral

part of the controller. Steady-state errors will be

levelled out as the summed error increases over

time until the control signal eventually matches the

load.

It is possible to set a limit for the control signal

generated by the integral part of the controller

(anti-windup).

Influence of the Integral factor

Integral factor

Integral factor:

KINT very small

steady-state position deviance

is very slowly regulated to zero;

KINT larger

faster regulation towards zero

steady-state position deviance,

larger overshoot;

KINT too large

heavy vibrations, instability.

Integration limit KILIM (21)

The

Inte

Inte gration limit

gration limit

sets a limit for the control sig-

nal generated by the integral part of the controller.

This helps to prevent the so called 'wind-up' pro-

blems which typically occurs in applications where

the overall control signal (the internal speed-refe-

rence) is maxed out for long periods of time.

This feature is also very helpful in applications where

the power to the motor is turned off and on while the

option card is controlling the VLT. Cutting of power to

the motor (by setting terminal 27 low) while little posi-

tioning deviance is present in the controller, could

result in an enormous control signal being generated

once the power is turned back on.

Velocity Feed-forward FFVEL (36)

The

Velocit

elocit

elocity feed

y feed

y feed ----- forward

forward

factor is a scaling factor

that is multiplied with the derivative of the setpoint

position (the velocity of the setpoint). The result of

this operation is added to the overall control signal.

This feature is especially useful in applications

where there is a good correlation between the

control signal (the VLT speed reference), and the

speed of the motor. This is indeed the case with

most applications using an asynchronous motor.

N B!

The scaling of the FFVEL parameter is de-

pendent on the correct setting of the maxi-

mum reference (VLT parameter #205) as well as

the SyncPos parameters VELMAX (1) and

ENCODER (2).

Optimizing the P

ID contr

oller

Содержание VLT5000 SyncPos













































































































































































































































Результаты поиска

Содержание VLT5000 SyncPos

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT5000 SyncPos, Руководство по эксплуатации

Результаты поиска

Содержание VLT5000 SyncPos

Отзывы:

Бренды по названию

Популярные бренды